Arthur Favrel

Dr. Arthur Favrel

Waseda Research Institute for Science and Engineering, Waseda University, Tokyo, Japan

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 June 2021 in Journal of Fluids Engineering
Verified
Journal Article
Closed access
PDF file
MKMohammad Hossein Khozaei
Mohammad Hossein Khozaei
AFArthur Favrel
Arthur Favrel
TMToshitake Masuko
Toshitake Masuko
NYNaoki Yamaguchi
Naoki Yamaguchi
Kazuyoshi MiyagawaKazuyoshi Miyagawa
Kazuyoshi Miyagawa
This paper focuses on the generation of twin vortex rope in the draft-tube elbow of a Francis turbine at deep part-load operation through analyzing the results of model tests along with numerical simulations. Model tests, including pressure fluctuations measurements, are conducted over ten speed factors. By considering the frequency of the pressure fluctuations with respect to the swirl intensity at the runner outlet, the part-load operating range is divided into three regimes, with two clear transitions between each occurring at swirl numbers 0.4 and 1.7. For operating conditions with a swirl number S > 0.4, a linear correlation between the frequency of the precessing vortex core and the swirl number is established. During the deep part-load regime (S > 1.7), low-frequency pressure fluctuations appear. Their frequency features another linear correlation with the swirl number. Unsteady computational fluid dynamics simulation of the full domain is performed to elucidate the generation mechanisms of the low-frequency fluctuations. By tracking the center of the vortical structures along the draft-tube, generation of three vortices in the elbow responsible for the pressure fluctuations at the lowest frequency is highlighted: the main precessing vortex core (PVC) hits the draft-tube wall in the elbow resulting in its break down into three vortices rotating with half the rotational speed of the PVC. Two of the vortices rotate with opposite angular position, constituting a structure of twin vortices. The periodic rotation of these three vortices in the elbow induces low-frequency pressure fluctuations.
1

28 June 2021 in Energies
Verified
Journal Article
Open access
PDF file
AFArthur Favrel
Arthur Favrel
NLNak-Joong Lee
Nak-Joong Lee
TITatsuya Irie
Tatsuya Irie
Kazuyoshi MiyagawaKazuyoshi Miyagawa
Kazuyoshi Miyagawa
This paper proposes an original approach to investigate the influence of the geometry of Francis turbines draft tube on pressure fluctuations and energy losses in off-design conditions. It is based on Design of Experiments (DOE) of the draft tube geometry and steady/unsteady Computational Fluid Dynamics (CFD) simulations of the draft tube internal flow. The test case is a Francis turbine unit of specific speed Ns=120 m-kW which is required to operate continuously in off-design conditions, either with 45% (part-load) or 110% (full-load) of the design flow rate. Nine different draft tube geometries featuring a different set of geometrical parameters are first defined by an orthogonal array-based DOE approach. For each of them, unsteady and steady CFD simulations of the internal flow from guide vane to draft tube outlet are performed at part-load and full-load conditions, respectively. The influence of each geometrical parameter on both the flow instability and resulting pressure pulsations, as well as on energy losses in the draft tube, are investigated by applying an Analysis of Means (ANOM) to the numerical results. The whole methodology enables the identification of a set of geometrical parameters minimizing the pressure fluctuations occurring in part-load conditions as well as the energy losses in both full-load and part-load conditions while maintaining the requested pressure recovery. Finally, the results of the CFD simulations with the final draft tube geometry are compared with the results estimated by the ANOM, which demonstrates that the proposed methodology also enables a rough preliminary estimation of the draft tube losses and pressure fluctuations amplitude.

11 September 2020 in Experiments in Fluids
Verified
Journal Article
Closed access
PDF file
AFArthur Favrel
Arthur Favrel
ZLZhihao Liu
Zhihao Liu
KMKazuyoshi Miyagawa
Kazuyoshi Miyagawa

27 January 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
JDJean Decaix
Jean Decaix
AMAndres Müller
Andres Müller
AFArthur Favrel
Arthur Favrel
FAFrançois Avellan
François Avellan
CMCécile Münch-Alligné
Cécile Münch-Alligné
The flow in a Francis turbine at full load is characterised by the development of an axial vortex rope in the draft tube. The vortex rope often promotes cavitation if the turbine is operated at a sufficiently low Thoma number. Furthermore, the vortex rope can evolve from a stable to an unstable behaviour. For CFD, such a flow is a challenge since it requires solving an unsteady cavitating flow including rotor/stator interfaces. Usually, the numerical investigations focus on the cavitation model or the turbulence model. In the present works, attention is paid to the strategy used for the time integration. The vortex rope considered is an unstable cavitating one that develops downstream the runner. The vortex rope shows a periodic behaviour characterized by the development of the vortex rope followed by a strong collapse leading to the shedding of bubbles from the runner area. Three unsteady RANS simulations are performed using the ANSYS CFX 17.2 software. The turbulence and cavitation models are, respectively, the SST and Zwart models. Regarding the time integration, a second order backward scheme is used excepted for the transport equation for the liquid volume fraction, for which a first order backward scheme is used. The simulations differ by the time step and the number of internal loops per time step. One simulation is carried out with a time step equal to one degree of revolution per time step and five internal loops. A second simulation used the same time step but 15 internal loops. The third simulations used three internal loops and an adaptive time step computed based on a maximum CFL lower than 2. The results show an influence of the time integration strategy on the cavitation volume time history both in the runner and in the draft tube with a risk of divergence of the solution if a standard set up is used.