This paper presents the results of the experimental research of 3D structures developed with an SLA additive technique using Durable Resin V2. The aim of this paper is to evaluate and compare the compression curves, deformation process and energy-absorption parameters of the topologies with different characteristics. The structures were subjected to a quasi-static axial compression test. Five different topologies of lattice structures were studied and compared. In the initial stage of the research, the geometric accuracy of the printed structures was analysed through measurement of the diameter of the beam elements at several selected locations. Compression curves and the stress history at the minimum cross-section of each topology were determined. Energy absorption parameters, including absorbed energy (AE) and specific absorbed energy (SAE), were calculated from the compression curves. Based on the analysis of the photographic material, the failure mode was analysed, and the efficiency of the topologies was compared.

This paper presents a characterization study of specimens manufactured from Ti-6Al-4V powder with the use of laser engineered net shaping technology (LENS). Two different orientations of the specimens were considered to analyze the loading direction influence on the material mechanical properties. Moreover, two sets of specimens, as-built (without heat treatment) and after heat treatment, were used. An optical measurement system was also adopted for determining deformation of the specimen, areas of minimum and the maximum principal strain, and an effective plastic strain value at failure. The loading direction dependence on the material properties was observed with a significant influence of the orientation on the stress and strain level. Microstructure characterization was examined with the use of optical and scanning electron microscopes (SEM); in addition, the electron backscatter diffraction (EBSD) was also used. The fracture mechanism was discussed based on the fractography analysis. The presented comprehensive methodology proved to be effective and it could be implemented for different materials in additive technologies. The material data was used to obtain parameters for the selected constitutive model to simulate the energy absorbing structures manufactured with LENS technology. Therefore, a brief discussion related to numerical modelling of the LENS Ti-6Al-4V alloy was also included in the paper. The numerical modelling confirmed the correctness of the acquired material data resulting in a reasonable reproduction of the material behavior during the cellular structure deformation process.

The strain gauge method and the digital image correlation (DIC) method are commonly employed for measuring strain in tested objects, including material specimens and structural elements. The optical method enables the assessment of 3D strain fields across the entire area of interest, achieved through cameras and advanced software. The study investigates both quasi-static strength tests and more advanced research of structures. It explores full-scale construction testing, featuring highly stressed components of new wagon designs. The paper reviews the benefits and challenges of using the DIC method to measure large-scale elements. Conducting full-scale object testing is characterized by significant complexity, often involving interactions between elements, complex loading conditions, and the influence of friction. Numerous factors affect the measurements. Therefore, to compare both methods, an initially standard shear by tensile test of CFRP composite was analyzed. The analysis of strain maps provides valuable visualization of deformation patterns occurring during construction loading. The strain gauge method was crucial for verifying the quality of the DIC measurements. The results obtained provide a detailed understanding of how the components behave, highlighting the versatility of digital image correlation technology. For strain values of 0.3% and above, a good match was obtained between optical and strain gauge measurements. Below this value, the results have less accuracy. The results obtained provide a detailed understanding of how the components behave, highlighting the versatility of digital image correlation technology. The error comparison and discussion between different measurement scenarios were conducted. The paper presents a developed methodology for measuring strain and displacement state in complex and crucial structural elements. The method can be applied to measurements of heavily loaded components used in the transportation industry; for example, in railways.

Cellular structures are increasingly utilized in modern engineering due to their exceptional mechanical and physical properties. In this study, the deformation and failure mechanisms of two energy-efficient lattice structures—hexagonal honeycomb and re-entrant honeycomb—were investigated. These structures were manufactured using additive stereolithography with light-curable Durable Resin V2. The experimental testing of the topologies under two perpendicular loading directions employed the 3D Digital Image Correlation (DIC) system to capture strain fields and deformation patterns, providing insights into structural behavior and failure mechanisms. The unit cells of the topologies were scaled up to enable precise optical measurements while preserving their structural interaction characteristics. Numerical simulations, conducted using the SAMP-1 material model in LS-DYNA and calibrated with tensile and compression test data, accurately replicated the behavior of the studied topologies and demonstrated good agreement with experimental results. The hexagonal structure, loaded along axis 2, showed the best fit, with deviations within 5%, while the re-entrant honeycomb structure exhibited weaker yet reasonable agreement. By integrating experimental and numerical approaches, the research validates the SAMP-1 model’s predictive capabilities for lattice structures and provides a framework for analyzing energy-absorbing lattice topologies.

This study presents an experimental investigation of an in-plane shear of a glass lamina composite using a ±45° off-axis tension test. Typically, the shear stress curve, shear modulus, and in-plane shear strength for composite lamina-type materials are identified. Previous research indicated that a loading rate affects the strength of this composite. This study extends the existing literature by utilising a non-contact optical digital image correlation (DIC) method to measure strain distribution during the test. Two cross-head displacement rates were examined. The obtained strain maps reveal an uneven distribution resembling fabric texture. As the deformation progresses, the differences in the strain pattern increase. Subsequently, a quantitative analysis of the differences between regions with extreme (minimum and maximum) strain values and regions with average values was conducted. Based on these measurements, shear stress–strain curves, indicating variations in their courses, were constructed. These differences may reach several percent and may influence the analysis of numerical simulations. The DIC results were validated using strain gauge measurements, a commonly utilised method in this test. It was demonstrated that the location of the strain gauge installation impacts the results. During the tests, the occurrence of multiple microcracks in the resin was observed, which can contribute to the nonlinearity observed in the shear stress–shear strain curve.