lei pei

Dr. lei pei


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 March 2019 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
LPlei pei
lei pei
HWhongbing wu
hongbing wu

22 October 2020 in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Verified
Journal Article
Closed access
PDF file
LPlei pei
lei pei
XSXuedao Shu
Xuedao Shu
Titanium alloys are widely used in the aerospace industry due to their superior properties such as high strength and low density. As a new titanium alloy with higher strength and lower heat conductivity, titanium alloy TC21 is very difficult to cut and the cutting mechanism of this alloy needs to be investigated deeply. In the paper, to observe the cutting phenomenon in the turning process of TC21 alloy, a series of turning experiments have been performed to investigate the turning process of TC21 alloy. Further, the influence of some important turning parameters (cutting speed, feed speed, depth of cut and rake angle) on cutting force and chip morphology is well analyzed through the experiments. In addition, a 3D finite element model for turning was established using the software ABAQUS for helping to analyze the turning process of TC21. Through simulation, cutting force, chip formation and temperature distribution of TC21 alloy in the turning process have been achieved. At the same time, simulated cutting forces and chip morphology were compared with the results of experiment. The results of experiments showed that the chip of TC21 alloy in turning process is serrated and the rake angle of tool has the obvious effect on the chip morphology.

14 October 2021 in PLOS ONE
Verified
Journal Article
Open access
PDF file
ZLZhang Lei
Zhang Lei
LPlei pei
lei pei
Due to the characteristics of high strength, high chemical activity and low heat conduction, titanium alloy materials are generally difficult to machine. As a typical titanium alloy with higher strength and lower heat conductivity, the machinability of titanium alloy TC21 is very poor and its cutting process is companied with larger cutting force and rapid tool wear. Straight-tooth milling tool is often used to cut the groove and side surface in the titanium alloy parts. And the milling method can be used to investigate the cutting mechanism because the cutting force has only two components and the better chip morphology is obtained. To investigate the straight-tooth milling process of TC21 alloy, a series of milling force experiments have been done. In addition, a 3D finite element model (FEM) for the straight-tooth milling process of TC21 alloy is presented to simulate the milling process. In the model, the constitutive material model, the failure model, the friction model and the heat transfer model were adopted. Through the simulation, chip formation, stress distribution, cutting force and milling temperature were obtained. The cutting force reaches its maximum when the spindle speed reaches about 13000 rpm, and then decreases as the speed continues to increase. The results confirmed that the similar “Salomon” phenomenon existed in the cutting process of TC21 alloy.

1 July 2021 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
PDF file
JWJanming Wu
Janming Wu
GLGuo Li
Guo Li
YTYaosheng Tan
Yaosheng Tan
CLChunfeng Liu
Chunfeng Liu
LPlei pei
lei pei
YHYu Hu
Yu Hu
The 289m high arch dam at Baihetan has good indicators before water storage, but after water storage, seepage gradually occurs in the dam body and foundation parts, which has some adverse effects on the safety of the dam. In this paper, five monitoring instruments were used to analyze the overall dam properties during the water storage process, including the pre-buried foundation corridor pressure tube, the dam base seepage pressure gauge, the seepage pressure tube around the dam, the dam water measuring weir and the dam base drainage hole. The results show that: the seepage pressure level before the curtain of the dam base is seriously affected by the upstream water level, Post-curtain and post-drainage lift pressure is less affected by upstream water level; the flow rate of the dam measuring weir and the dam base drainage hole is more affected by the upstream water level, and the trend of flow rate changes is more consistent with the trend of the upstream water level; the rest of the parts are less affected by the upstream water level.

30 September 2019 in Transactions of the Indian Institute of Metals
Verified
Journal Article
Closed access
PDF file
LPlei pei
lei pei
CLChuan Liu
Chuan Liu
Xuedao ShuXuedao Shu
Xuedao Shu

6 November 2021
Verified
Conference Paper
Closed access
YFYuchen Fu
Yuchen Fu
YTYaosheng Tan
Yaosheng Tan
Yu HuYu Hu
Yu Hu
CLChunfeng Liu
Chunfeng Liu
LPlei pei
lei pei
YWYajun WANG
Yajun WANG
Based on the prototype monitoring results of a super high arch dam during the impoundment period in Southwest China, this paper systematically analyzes and researches the existing monitoring results, preliminarily evaluates the operation status of the dam during impoundment period, and better demonstrates the performance of different monitoring instruments through the QH3D software monitoring results. The results are compared with the three-dimensional finite element results, and the mechanism of stress and deformation of an extra-high arch dam in southwest China during impoundment is studied in depth. This study can find the potential risk of the dam in time, and give early warning of the serious problems such as cracks in the dam body and key parts.