Wojciech Szczypinski-Sala

Dr. Wojciech Szczypinski-Sala

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 January 2020 in Materials
Verified
Journal Article
Open access
PDF file
WSWojciech Szczypinski-Sala
Wojciech Szczypinski-Sala
JLJanusz Lubas
Janusz Lubas
This paper presents the outcome of the measurement of the tribological characteristic of O-ring seals in the event of operating in conditions with a lack of lubrication. The measurement was carried out on a seal and rod model. The measurement was carried out during the condition of the round cross-section seal sliding on the surface of the piston rod. We analyzed how the friction force during rod movement, which resulted from the cooperation of the sliding nod and the rod, was changing. The experiment was conducted for various rubber materials. The aim of the research was to evaluate the friction reducing capability of graphite in rubbers of commercial sealing parts. Typical materials used for the seal and the materials, which contained the filler in the form of graphite powder, were compared. Synthetic graphite powder with a particle size of 1–2 µm was applied, and nitrile rubber (NBR) and fluoroelastomer (FKM) were compared as typical materials for O-ring seals. In the case of the two tested materials, the addition of graphite powder had an influence on the decrease in the friction force.

20 December 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
WSWojciech Szczypinski-Sala
Wojciech Szczypinski-Sala
AKAdam Kot
Adam Kot
MHMateusz Hankus
Mateusz Hankus
The main aim of this article is to present the possibility of assessing the intensity of the impact of vibrations on vehicle users. During vehicle operation, many factors can have impacts on changes in the characteristics of car suspension, which can affect passenger comfort. This paper presents the results obtained from calculations based on a mathematical model, as well as from measurements during laboratory tests. The tests were performed on vehicles that differed in characteristics of damping suspension. The tests were carried out using a test stand for evaluating the effectiveness of shock absorbers in vehicles. During the tests, vibration propagations on the driver’s seat and the steering wheel were evaluated. An analysis of the amplitudes and frequencies of vibrations experienced by occupants was carried out. A method for assessing the impact of changes in the damping characteristics of a suspension system on vehicle users’ comfort during technical inspection was proposed.

19 December 2020 in Materials
Verified
Journal Article
Open access
PDF file
JLJanusz Lubas
Janusz Lubas
WSWojciech Szczypinski-Sala
Wojciech Szczypinski-Sala
Paweł WośPaweł Woś
Paweł Woś
EZEdyta Zielińska
Edyta Zielińska
KMKrzysztof Miernik
Krzysztof Miernik
The present study discusses the influence of engine oils on the tribological parameters of sliding couples with laser borided surface layer. The borided layer was formed on specimens made from AISI 5045 steel by laser remelting of a surface layer coated with amorphous boron. The sliding friction and wear process was carried out on the pairs with AISI 5045 steel and SAE-48 bearing alloys which were lubricated with 5W-40 and 15W-40 engine oils. The investigation showed significant differences in the friction coefficient and temperature in the tested pairs with the laser borided surface layer. In the couples lubricated with 5W-40 engine oil, the tested parameter of friction was higher than in the couples lubricated with 15W-40 engine oil. The couples lubricated with 5W-40 engine oil showed more intensive wear of SAE-48 bearing alloy in contact with the laser borided surface layer than the pairs lubricated with 15W-40 engine oil. The laser borided surface layer used in friction pairs leads to the destruction of the lubricating properties of engine oils and reduces its resistance to scuffing.

11 October 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
AKAdam Kot
Adam Kot
WGW Grzegożek
W Grzegożek
WSWojciech Szczypinski-Sala
Wojciech Szczypinski-Sala
This work deals with the analysis of the CVT efficiency for three different rubber V-belts. The bench tests have been conducted on the complete light two-wheeled vehicle drive system so the experiments refer to real exploitation conditions. The research has been performed for fixed gear ratios. The overall efficiency and belt slip have been specified. The longitudinal belt velocity has been measured by the contactless measurement head. The basic belts physical properties have been estimated and significant dissimilarities of their construction details, used materials and stiffness parameters have been revealed. The explicit differences of overall efficiency and belt slip have been observed between tested belts. The V-belt features limiting specified type of losses contributes to increasing other losses at the same time. Furthermore the gear ratio essential influence on the belt slip has been noticeable. The amount of slip value indicates that this is significant part of the total power losses as it has been described by Bertini. However it clashes with the Chen research, where the slip corresponds with the marginal part of the overall losses.

11 October 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
WSWojciech Szczypinski-Sala
Wojciech Szczypinski-Sala
KDK Dobaj
K Dobaj
In the paper, the results of the research were discussed, the aim of which was the estimation of the friction coefficient of brake pad- brake disc during braking a vehicle with regard to the influence of external conditions. B Segment vehicle with independent suspension was used for measurement and tests. Test brakes were made on the drum test stand the moment of inertia of which was chosen so that kinetic energy lost during the test would be the same as during road tests. The step of wetting of the brake disc and pads was taken into consideration during the research. The research was conducted comparatively for the vehicle with acting anti-lock braking system and subsequently for the vehicle without the system. The friction materials used in disc brake systems are required to provide a stable friction coefficient. From the point of view of efficiency of operation the brake system, the characteristics of the variation of friction coefficient of the brake disc and pads have a special meaning. Neural network was applied to estimate the value of friction coefficient during braking. The results obtained during the measurements were compared to the estimated values.

11 October 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
WSWojciech Szczypinski-Sala
Wojciech Szczypinski-Sala
JLJanusz Lubas
Janusz Lubas
The aim of the present work is to determine the influence of TiB2 coating on the friction parameters in sliding pairs under lubricated friction conditions. The TiB2 coating deposited on modified surface layers of ring specimens made of 46Cr2 steel were matched under test conditions with counterparts made of CuPb30 bearing alloys. The tested sliding pairs were lubricated with 15W/40 mineral oil and 5W/40 synthetic engine oil. The lubrication of friction area with mineral oil causes the reduction of friction force and temperature in the friction area, whereas the lubrication with synthetic oil reduces the wear of the bearing and the changes in the geometrical structure of the cooperating friction pair elements. Lubrication of the friction area in the start-up phase of the friction pair by mineral oil causes faster stabilization of the friction conditions in the contact area than in case of lubrication of the friction pair by the synthetic oil.