Wilhelm Johannisson

Mr. Wilhelm Johannisson

KTH Royal Institute of Technology

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 November 2017 in Journal of Materials Chemistry A
Verified
Journal Article
Open access
PDF file
NIN. Ihrner
N. Ihrner
WJWilhelm Johannisson
Wilhelm Johannisson
FSF. Sieland
F. Sieland
DZDan Zenkert
Dan Zenkert
MJM. Johansson
M. Johansson
For the realization of structural batteries, electrolytes where both higher ionic conductivity and stiffness are combined need to be developed. The present study describes the formation of a structural battery electrolyte (SBE) as a two phase system using reaction induced phase separation. A liquid electrolyte phase is combined with a stiff vinyl ester based thermoset matrix to form a SBE. The effect of monomer structure variations on the formed morphology and electrochemical and mechanical performance has been investigated. An ionic conductivity of 1.5 × 10−4 S cm−1, with a corresponding storage modulus (E′) of 750 MPa, has been obtained under ambient conditions. The SBEs have been combined with carbon fibers to form a composite lamina and evaluated as a battery half-cell. Studies on the lamina revealed that both mechanical load transfer and ion transport are allowed between the carbon fibers and the electrolyte. These results pave the way for the preparation of structural batteries using carbon fibers as electrodes.

1 July 2018 in Composites Science and Technology
Verified
Journal Article
Closed access
JHJohan Hagberg
Johan Hagberg
HMHenry A. Maples
Henry A. Maples
KAKayne S.P. Alvim
Kayne S.P. Alvim
JXJohanna Xu
Johanna Xu
WJWilhelm Johannisson
Wilhelm Johannisson
GLGöran Lindbergh
Göran Lindbergh

1 November 2018 in Composites Science and Technology
Verified
Journal Article
Open access
WJWilhelm Johannisson
Wilhelm Johannisson
NINiklas Ihrner
Niklas Ihrner
DZDan Zenkert
Dan Zenkert
MJMats Johansson
Mats Johansson
DCDavid Carlstedt
David Carlstedt
FSFabian Sieland
Fabian Sieland

1 September 2019 in Multifunctional Materials
Verified
Journal Article
Open access
PDF file
WJWilhelm Johannisson
Wilhelm Johannisson
DZDan Zenkert
Dan Zenkert
GLGöran Lindbergh
Göran Lindbergh

1 September 2021 in Multifunctional Materials
Verified
Journal Article
Open access
WJWilhelm Johannisson
Wilhelm Johannisson
DCDavid Carlstedt
David Carlstedt
ANAwista Nasiri
Awista Nasiri
CBChristina Buggisch
Christina Buggisch
PLPeter Linde
Peter Linde
Bodo FiedlerBodo Fiedler
Bodo Fiedler
Structural carbon fibre composite batteries are a type of multifunctional batteries that combine the energy storage capability of a battery with the load-carrying ability of a structural material. To extract the current from the structural battery cell, current collectors are needed. However, current collectors are expensive, hard to connect to the electrode material and add mass to the system. Further, attaching the current collector to the carbon fibre electrode must not affect the electrochemical properties negatively or requires time-consuming, manual steps. This paper presents a proof-of-concept method for screen-printing of current collectors for structural carbon fibre composite batteries using silver conductive paste. Current collectors are screen-printed directly on spread carbon fibre tows and a polycarbonate carrier film. Experimental results show that the electrochemical performance of carbon fibre vs lithium metal half-cells with the screen-printed collectors is similar to reference half-cells using metal foil and silver adhered metal-foil collectors. The screen-printed current collectors fulfil the requirements for electrical conductivity, adhesion to the fibres and flexible handling of the fibre electrode. The screen-printing process is highly automatable and allows for cost-efficient upscaling to large scale manufacturing of arbitrary and complex current collector shapes. Hence, the screen-printing process shows a promising route to realization of high performing current collectors in structural batteries and potentially in other types of energy storage solutions.

14 October 2019 in Sustainability
Verified
Journal Article
Open access
PDF file
MZMats Zackrisson
Mats Zackrisson
CJChristina Jönsson
Christina Jönsson
WJWilhelm Johannisson
Wilhelm Johannisson
KFKristin Fransson
Kristin Fransson
SPStefan Posner
Stefan Posner
GLGöran Lindbergh
Göran Lindbergh
With increasing interest in reducing fossil fuel emissions, more and more development is focused on electric mobility. For electric vehicles, the main challenge is the mass of the batteries, which significantly increase the mass of the vehicles and limits their range. One possible concept to solve this is incorporating structural batteries; a structural material that both stores electrical energy and carries mechanical load. The concept envisions constructing the body of an electric vehicle with this material and thus reducing the need for further energy storage. This research is investigating a future structural battery that is incorporated in the roof of an electric vehicle. The structural battery is replacing the original steel roof of the vehicle, and part of the original traction battery. The environmental implications of this structural battery roof are investigated with a life cycle assessment, which shows that a structural battery roof can avoid climate impacts in substantive quantities. The main emissions for the structural battery stem from its production and efforts should be focused there to further improve the environmental benefits of the structural battery. Toxicity is investigated with a novel chemical risk assessment from a life cycle perspective, which shows that two chemicals should be targeted for substitution.