This paper presents a review of the expectations and challenges of using biomass in the prevention and slowing of paraffin wax deposition that takes place during the crude oil production process. The inhibition of the deposition process involves the use of solvents from biomass that are generally available around the crude oil production field. The processes used to scale down the precipitation of wax include mixing crude oil with the manufacturer’s solvent composed of toluene and xylene. The goal is to assess solvents sourced from biomass that are capable to slow down the wax deposition process. Wax appearance temperature is an important characteristic to evaluate the possible wax precipitation of a given fluid. Wax precipitation can be reduced by using some chemical additives, often called the pour point depressant. This additive is expected to be produced from local biomass which can compete with solvents currently produced on the market.
31 October 2018 in Journal of Earth Energy Engineering
Low salinity waterflooding (LSW) is categorized as one of emerging EOR technologies. It is done by injecting water with different salt composition and/or concentration. The research has been carried out for both sandstone and carbonate with the results looks promising. However, most of this research still concentrated in the north sea, middle east and North America region. This article discusses the applicability of low salinity waterflooding methodology in Indonesia. Spontaneous imbibition test is carried out to observe the recovery gain from a various combination of concentration and composition of the injected brine. The change of pH of the brine is also examined in order to confirm the pH effect mechanism. Three different concentration of brine (500 ppm, 5.000 ppm, and 10.000 ppm), three different brine composition (NaCl, CaCl2, and MgCl2) and high paraffinic crude oil are used as the fluid sample. It is found that the increased oil recovery is significant at a salinity of 10,000 ppm for MgCl2 and 5,000 ppm for NaCl ions. While the lowest recovery was shown by the test at a salinity of 500 ppm
22 February 2018 in IOP Conference Series: Materials Science and Engineering
Waxy oil has been the main characteristics of The X field. Initial screening criteria studies indicated that cyclic steam stimulation (CSS) would be the optimum option because favorable reservoir condition. Based on this method we would like to know how much oil gain and the effect of steam for the stimulated and surrounding well. The injection of steam was done for 7 days followed by 14 days of soaking period. 39,000 liter of Marine fuel oil was used to generate steam for stimulation with an average produce steam quality about 80%. Average of 255 MMBTU of steam was injected each day with total steam injected was about 1.7 BBTU. The oil production was increased four times from 5 bopd into 21 bopd. Proper well candidate and high permeability are some reason for this method successfully increase oil production. Additional heat from steam reduced the damage near wellbore due to wax deposition. This is verifying by increasing productivity index from 3 bbl/psi to 4 bbl/psi. From results and observation data, this method can be a platform for typical shallow depth reservoir with high paraffinic content especially other reservoir in Sihapas formation.
20 October 2020 in Journal of Earth Energy Engineering
Wax paraffin deposition is a problem faced in the pipeline for petroleum industries that they blockage the partial or full inside the pipe, which will decrease the production rate. One of the treatments is to use the preventive methods called wax inhibitors which are expected to inhibit the crystallization of paraffin wax, and bio-solvent is included. Hydrolysis and fermentation technique are used to produced bio-solvent. Hydrolysis aims to break lignin and hemicellulose, damage the crystal structure, and increase the porosity of the material. At the same time, the occurrence of pentose changes and some glucose into ethanol is present in the fermentation process. Then, purified by the distillation process to obtain bio solvent products that are applied with waxy crude oil can reduce the pour point value of crude oil. From the hydrolysis process with five variations of acid percentage, the amount of reducing sugars increase. By increasing temperature from 50 ° C to 100 ° C, the reducing sugars continues to increase until it reaches the optimal point of 18.2 ° Brix. The amount of inoculant also affects the level of bio-solvent where the optimum results using inoculants are 0.015 g/mL, which produces 6% levels of bioethanol. The high ethanol content of 2% had a density value of 0.979 g/mL. The best °API at 5% is 13.901, and the average value is about 13.0945, where the best viscosity values for ethanol content of 6% are 0.814. Bioethanol testing using waxy crude oil is carried out with the bioethanol content of 6%. The addition of the ethanol contents only decreased the pour point 2-3℃. At sample, #LGK19 experienced a 3°C drop in pour point from 45°C to 42°C. Therefore, it can be concluded that bioethanol used as a solvent can potentially inhibit paraffin deposition.