Baher Azzam

Mr. Baher Azzam

Center for Wind Power Drives, RWTH Aachen University
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 March 2021 in Forschung im Ingenieurwesen
Verified
Journal Article
Open access
PDF file
BABaher Azzam
Baher Azzam
RSRalf Schelenz
Ralf Schelenz
BRBjörn Roscher
Björn Roscher
ABAbdul Baseer
Abdul Baseer
GJGeorg Jacobs
Georg Jacobs
A current development trend in wind energy is characterized by the installation of wind turbines (WT) with increasing rated power output. Higher towers and larger rotor diameters increase rated power leading to an intensification of the load situation on the drive train and the main gearbox. However, current main gearbox condition monitoring systems (CMS) do not record the 6‑degree of freedom (6-DOF) input loads to the transmission as it is too expensive. Therefore, this investigation aims to present an approach to develop and validate a low-cost virtual sensor for measuring the input loads of a WT main gearbox. A prototype of the virtual sensor system was developed in a virtual environment using a multi-body simulation (MBS) model of a WT drivetrain and artificial neural network (ANN) models. Simulated wind fields according to IEC 61400‑1 covering a variety of wind speeds were generated and applied to a MBS model of a Vestas V52 wind turbine. The turbine contains a high-speed drivetrain with 4‑points bearing suspension, a common drivetrain configuration. The simulation was used to generate time-series data of the target and input parameters for the virtual sensor algorithm, an ANN model. After the ANN was trained using the time-series data collected from the MBS, the developed virtual sensor algorithm was tested by comparing the estimated 6‑DOF transmission input loads from the ANN to the simulated 6‑DOF transmission input loads from the MBS. The results show high potential for virtual sensing 6‑DOF wind turbine transmission input loads using the presented method.

10 October 2018 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
FHF. Harzendorf
F. Harzendorf
BABaher Azzam
Baher Azzam
RSR. Schelenz
R. Schelenz
GJGeorg Jacobs
Georg Jacobs
Innovation in the wind turbine's drivetrain are mainly motivated by the goal to have better products. To have an improved final product, it should be analysed in a holistic manner over the drivetrains lifetime. One essential lifetime phase of a wind turbines drivetrain is the manufacturing phase, which is focused in this analysis. This paper presents a way to estimate manufacturing cost of wind turbine drivetrains at an early design phase. The approach is based on literature and expert interviews as well as their abstractions. The target audience are people involved in the development of new wind turbine drivetrain concepts. To customize the approach for their requirements, it is based on a minimum number of necessary input mainly geometric component specification. This approach is modular, scalable and applicable on to future drivetrain concepts. The used approach proves to be an effective way for estimating manufacturing costs of drivetrain components. A comparative analysis against a benchmark application, a 5 MW wind turbine's drivetrain, confirms the accuracy of the presented approach. A case study dealing with two possible gearbox solutions with a power rating over 5 MW underlines the importance of taking manufacturing cost in consideration when thinking about new developments in wind turbine drivetrain technology.

14 December 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
BABaher Azzam
Baher Azzam
FHFreia Harzendorf
Freia Harzendorf
RSRalf Schelenz
Ralf Schelenz
Walter HolwegerWalter Holweger
Walter Holweger
GJGeorg Jacobs
Georg Jacobs
White etching crack (WEC) failure is a failure mode that affects bearings in many applications, including wind turbine gearboxes, where it results in high, unplanned maintenance costs. WEC failure is unpredictable as of now, and its root causes are not yet fully understood. While WECs were produced under controlled conditions in several investigations in the past, converging the findings from the different combinations of factors that led to WECs in different experiments remains a challenge. This challenge is tackled in this paper using machine learning (ML) models that are capable of capturing patterns in high-dimensional data belonging to several experiments in order to identify influential variables to the risk of WECs. Three different ML models were designed and applied to a dataset containing roughly 700 high- and low-risk oil compositions to identify the constituting chemical compounds that make a given oil composition high-risk with respect to WECs. This includes the first application of a purpose-built neural network-based feature selection method. Out of 21 compounds, eight were identified as influential by models based on random forest and artificial neural networks. Association rules were also mined from the data to investigate the relationship between compound combinations and WEC risk, leading to results supporting those of previous analyses. In addition, the identified compound with the highest influence was proved in a separate investigation involving physical tests to be of high WEC risk. The presented methods can be applied to other experimental data where a high number of measured variables potentially influence a certain outcome and where there is a need to identify variables with the highest influence.

11 May 2022 in Sensors
Verified
Journal Article
Open access
PDF file
BABaher Azzam
Baher Azzam
RSRalf Schelenz
Ralf Schelenz
GJGeorg Jacobs
Georg Jacobs
The ongoing trend of building larger wind turbines (WT) to reach greater economies of scale is contributing to the reduction in cost of wind energy, as well as the increase in WT drivetrain input loads into uncharted territories. The resulting intensification of the load situation within the WT gearbox motivates the need to monitor WT transmission input loads. However, due to the high costs of direct measurement solutions, more economical solutions, such as virtual sensing of transmission input loads using stationary sensors mounted on the gearbox housing or other drivetrain locations, are of interest. As the number, type, and location of sensors needed for a virtual sensing solutions can vary considerably in cost, in this investigation, we aimed to identify optimal sensor locations for virtually sensing WT 6-degree of freedom (6-DOF) transmission input loads. Random forest (RF) models were designed and applied to a dataset containing simulated operational data of a Vestas V52 WT multibody simulation model undergoing simulated wind fields. The dataset contained the 6-DOF transmission input loads and signals from potential sensor locations covering deformations, misalignments, and rotational speeds at various drivetrain locations. The RF models were used to identify the sensor locations with the highest impact on accuracy of virtual load sensing following a known statistical test in order to prioritize and reduce the number of needed input signals. The performance of the models was assessed before and after reducing the number of input signals required. By allowing for a screening of sensors prior to real-world tests, the results demonstrate the high promise of the proposed method for optimizing the cost of future virtual WT transmission load sensors.

1 June 2015
Verified
Conference Paper
Closed access
JMJitaditya Mondal
Jitaditya Mondal
BABaher Azzam
Baher Azzam
MAMousa Abuhalaiqa
Mousa Abuhalaiqa
RTReza Tafreshi
Reza Tafreshi
The objective of this paper is to demonstrate the design and implementation of an Active Tuned Mass Damper (ATMD) and to determine its effectiveness experimentally and theoretically. ATMDs are damping units placed in structures where a mass is actuated to move out of phase with respect to the movement of the structure to reduce vibrations. In this paper, an ATMD is used to reduce the vibrations of a scaled-down four-story building. The building is subjected to base excitation through a crank-slider motor mechanism on the bottom floor. The ATMD consists of a mass which is actuated through a DC motor. Using feedback from an accelerometer placed on the topmost floor, a proportional gain controller is implemented through LabVIEW to control the motion of the mass. The results show that the ATMD system has damped approximately 49.7% of the vibrational amplitude.

27 December 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
BABaher Azzam
Baher Azzam
RSRalf Schelenz
Ralf Schelenz
MCMartin Cardaun
Martin Cardaun
GJGeorg Jacobs
Georg Jacobs
The trend of increasing the power output and nominal load capacities of wind turbines (WT) over time has been driving the construction of testing facilities with increasing load capacities for testing WT drivetrain components prior to field deployment. Due to the high investment and operational costs of such facilities, a need exists to design accelerated tests that cover load situations corresponding to expected field conditions while maintaining high time-efficiency. This investigation addresses this need by presenting a methodology to achieve the following goals. Firstly, identifying ranges and combinations of WT 6-degree of freedom (6-DOF) rotor loads is to be expected in the field. This is achieved using aeroelastic multibody simulations (MBS) of an MBS WT model being subjected to simulated wind fields covering the design load cases outlined in the IEC 61400-1 standard and by analyzing the simulated time-series data to design accelerated tests that efficiently and realistically cover the design space of the variables, e.g., 6-DOF rotor loads, to be applied during WT drivetrain testing. The designed tests are to take place on a purpose-built test rig that allows for the application and control of the 6-DOF drivetrain input loads and rotational speed. Using the proposed method, accelerated tests were designed that efficiently cover load combinations within the realistic regions of the design space. A comparison with a full factorial design of experiments shows a significant (95+ %) reduction in total test time as well as the ability of the proposed method to help to avoid unsustainable and unrealistic load conditions within the design space that could result in costly, unintended drivetrain failures during testing.