Black phosphorus (BP) has emerged as a promising two-dimensional (2D) material for next generation transistor applications due to its superior carrier transport properties. Among other issues, achieving reduced subthreshold swing and enhanced hole mobility simultaneously remains a challenge which requires careful optimization of the BP/gate oxide interface. Here, we report the realization of high performance BP transistors integrated with HfO2 high-k gate dielectric using a low temperature CMOS process. The fabricated devices were shown to demonstrate a near ideal subthreshold swing (SS) of ~69 mV/dec and a room temperature hole mobility of exceeding >400 cm2/Vs. These figure-of-merits are benchmarked to be the best-of-its-kind, which outperform previously reported BP transistors realized on traditional SiO2 gate dielectric. X-ray photoelectron spectroscopy (XPS) analysis further reveals the evidence of a more chemically stable BP when formed on HfO2 high-k as opposed to SiO2, which gives rise to a better interface quality that accounts for the SS and hole mobility improvement. These results unveil the potential of black phosphorus as an emerging channel material for future nanoelectronic device applications.
31 January 2017 in Journal of Materials Chemistry C
We demonstrate the direct formation of c-axis oriented crystalline IGZO thin films at room temperature by magnetron sputtering. The influence of processing parameters such as oxygen partial pressure, post-annealing temperature and channel thickness on the electrical performance of IGZO films and thin-film transistors (TFTs) was intensively investigated. The as-deposited crystalline IGZO TFTs exhibited a mobility of 4.49 cm2 V−1 s−1 and an on/off ratio of 2.08 × 107. For the annealed device, a high mobility of 10.51 cm2 V−1 s−1, a subthreshold swing of 0.672 V decade−1, a threshold voltage of 0.38 V, as well as an on/off current ratio of ∼108 are achieved with an annealing temperature of 400 °C. These results present a significant step towards the development of high-performance TFTs using oriented crystalline IGZO.
Thin-film transistors (TFTs) made of metal oxide semiconductors are now increasingly used in flat-panel displays. Metal oxides are mainly fabricated via vacuum-based technologies, but solution approaches are of great interest due to the advantages of low-cost and high-throughput manufacturing. Unfortunately, solution-processed oxide TFTs suffer from relatively poor electrical performance, hindering further development. Recent studies suggest that this issue could be solved by introducing a novel heterojunction strategy. This article reviews the recent advances in solution-processed heterojunction oxide TFTs, with a specific focus on the latest developments over the past five years. Two of the most prominent advantages of heterostructure oxide TFTs are discussed, namely electrical-property modulation and mobility enhancement by forming 2D electron gas. It is expected that this review will manifest the strong potential of solution-based heterojunction oxide TFTs towards high performance and large-scale electronics.
BaTiO3/polymer/Al (BPA) composite films for energy storage were fabricated by way of a roll coating and thermal curing process. The coating slurry consisted of silicon-containing heat-resistant resin (CYN-01) and BaTiO3 particles with various particle sizes obtained from commercial BaTiO3 powders processed at different durations of wet sand grinding in the presence of silane coupling agent (KH550), which not only improves the dielectric performance of the BPA films but also facilitates its production in a large scale. The major influence factors, such as the ratio between BaTiO3 and resin and the size of BaTiO3 particles, were investigated and their related mechanisms were discussed. The results show that modifying BaTiO3 particles (D90 = 0.83 μm) with the silane coupling agent of KH550 enhances the dielectric properties of the BPA films. The typical BPA films obtained exhibit a high dielectric constant of 32, a high break strength of 20.8 V/μm and a low dielectric loss of 0.014. The present work provides a simple and convenient way to prepare high-quality ceramic/polymer composite films for energy-storage application in a large scale.
Simple but robust growth of spherical BaTiO3 nanoparticles with uniform nanoscale sizes is of great significance for the miniaturization of BaTiO3-based electron devices. This paper reports a TiO2-seeded hydrothermal process to synthesize spherical BaTiO3 nanoparticles with a size range of 90–100 nm using TiO2 (Degussa) and Ba(NO3)2 as the starting materials under an alkaline (NaOH) condition. Under the optimum conditions ([NaOH] = 2.0 mol L−1, RBa/Ti = 2.0, T = 210 °C and t = 8 h), the spherical BaTiO3 nanoparticles obtained exhibit a narrow size range of 91 ± 14 nm, and the corresponding BaTiO3/polymer/Al film is of a high dielectric constant of 59, a high break strength of 102 kV mm−1, and a low dielectric loss of 0.008. The TiO2-seeded hydrothermal growth has been proved to be an efficient process to synthesize spherical BaTiO3 nanoparticles for potential capacitor energy-storage applications.