Strong waveform complexities, including multipathing of the S diffracted phase and rapid changes in differential ScS‐S times, are observed for multiple deep Fiji earthquakes recorded at the USArray. The complexities occur at the northeastern edge of the Pacific Large Low Shear Velocity Province (LLSVP), about 12 degrees southeast of present‐day Hawaiʻi. Waveform modeling of the multipathing provides good constraints on an ultra‐low velocity zone (ULVZ) with a width of 5 degree located near the inner edge of the LLSVP. Based on the mineralogical‐modeling of the ULVZ as a solid iron‐rich magnesiowüstite‐bearing assemblage with compatible morphology predicted from geodynamical simulations, a ULVZ model with a thickness of 30 km and a shear wave velocity reduction of 18% is preferred. The rapid change in differential ScS‐S travel time is best explained by having both the aforementioned ULVZ and an adjacent high velocity structure near the LLSVP. Furthermore, a low‐velocity plume‐like structure could potentially explain the observed S travel time delay independent of ScS. These seismic features are proposed to be a ULVZ driven toward the edge of the LLSVP while potentially pushed by a subducted slab. This configuration may trigger plume generation due to strong thermal instabilities and is in the same vicinity where mantle flow models place the present‐day Hawaiian plume source. Multiple ScS can potentially be used to verify vertical plume structure in tomographic models but the accuracy of upper mantle structure, which is a key reflection point, needs to be considered.

The high-pressure melting curve of FeO controls key aspects of Earth’s deep interior and the evolution of rocky planets more broadly. However, existing melting studies on wüstite were conducted across a limited pressure range and exhibit substantial disagreement. Here we use an in-situ dual-technique approach that combines a suite of >1000 x-ray diffraction and synchrotron Mössbauer measurements to report the melting curve for Fe_1-xO wüstite to pressures of Earth’s lowermost mantle. We further observe features in the data suggesting an order-disorder transition in the iron defect structure several hundred kelvin below melting. This solid-solid transition, suggested by decades of ambient pressure research, is detected across the full pressure range of the study (30 to 140 GPa). At 136 GPa, our results constrain a relatively high melting temperature of 4140 ± 110 K, which falls above recent temperature estimates for Earth’s present-day core-mantle boundary and supports the viability of solid FeO-rich structures at the roots of mantle plumes. The coincidence of the defect order-disorder transition with pressure-temperature conditions of Earth’s mantle base raises broad questions about its possible influence on key physical properties of the region, including rheology and conductivity.

The composition of ultralow velocity zones (ULVZs) remains an open question, despite advances in both seismology and experimental work. We investigate the hypothesis of iron-rich (Mg,Fe)O (magnesiowüstite) as a cause of ULVZ seismic signatures. We report new quasi-hydrostatic X-ray diffraction measurements to constrain the equation of state of (Mg_0.06Fe_0.94)O with fit parameters V₀ = 9.860 ± 0.007 ų, K_0T = 155.3 ± 2.2 GPa, K’_0T = 3.79 ± 0.11, as well as synchrotron Mössbauer spectroscopy measurements to characterize the high-pressure magnetic and spin state of magnesiowüstite. We combine these results with information from previous studies to calculate the elastic behavior at core–mantle boundary conditions of magnesiowüstite, as well as coexisting bridgmanite and calcium silicate perovskite. Forward models of aggregate elastic properties are computed, and from these, we construct an inverse model to determine the proportions of magnesiowüstite that best reproduce ULVZ observations within estimated mutual uncertainties. We find that the presence of magnesiowüstite can explain ULVZ observations exhibiting 1:2 V_P:V_S reduction ratios relative to the Preliminary Reference Earth Model (PREM), as well as certain 1:3 V_P:V_S reductions within estimated uncertainty bounds. Our work quantifies the viability of compositionally distinct ULVZs containing magnesiowüstite and contributes to developing a framework for a methodical approach to evaluating ULVZ hypotheses.

Seismic and mineralogical studies have suggested regions at Earth’s core-mantle boundary may be highly enriched in FeO, reported to exhibit metallic behavior at extreme pressure-temperature (P–T) conditions. However, underlying electronic processes in FeO remain poorly understood. Here we explore the electronic structure of B1-FeO at extreme conditions with large-scale theoretical modeling using state-of-the-art embedded dynamical mean field theory (eDMFT). Fine sampling of the phase diagram reveals that, instead of sharp metallization, compression of FeO at high temperatures induces a gradual orbitally selective insulator-metal transition. Specifically, at P–T conditions of the lower mantle, FeO exists in an intermediate quantum critical state, characteristic of strongly correlated electronic matter. Transport in this regime, distinct from insulating or metallic behavior, is marked by incoherent diffusion of electrons in the conducting t_2g orbital and a band gap in the e_g orbital, resulting in moderate electrical conductivity (~10⁵ S/m) with modest P–T dependence as observed in experiments. Enrichment of solid FeO can thus provide a unifying explanation for independent observations of low seismic velocities and elevated electrical conductivities in heterogeneities at Earth’s mantle base.

When diamond anvil cell (DAC) sample chambers are outfitted with both thermal insulation and electrodes, two cutting-edge experimental methods are enabled: Joule heating with spectroradiometric temperature measurement and electrical resistance measurements of samples heated to thousands of kelvin. The accuracy of temperature and resistance measurements, however, often suffers from poor control of the shape and location of the sample, electrodes, and thermal insulation. Here, we present a recipe for the reproducible and precise fabrication of DAC sample, electrodes, and thermal insulation using a three-layer microassembly. The microassembly contains two potassium chloride thermal insulation layers, four electrical leads, a sample, and a buttressing layer made of polycrystalline alumina. The sample, innermost electrodes, and buttress layer are fabricated by focused-ion-beam milling. Three iron samples are presented as proof of concept. Each is successfully compressed and pulsed Joule heated while maintaining a four-point probe configuration. The highest pressure-temperature condition achieved is ∼150 GPa and 4000 K.