This paper focuses on developing, fabricating, and characterizing composite polycaprolactone (PCL) membranes reinforced with titanium dioxide nanoparticles (NPs) elaborated by using two solvents; acetic acid and a mixture of chloroform and N,N-dimethylformamide (DMF). The resulting physical, chemical, and mechanical properties of the composite materials are studied by using experimental characterization techniques such as scanning electron microscopy (SEM), differential scanning calorimetry (DSC), X-ray diffraction (XRD), Fourier-transform infrared (FTIR) analysis, contact angle (CA), uniaxial and biaxial tensile tests, and surface roughness measurements. Experimental results show that the composite material synthesized by sol-gel and chloroform-DMF has a better performance than the one obtained by using acetic acid as a solvent.

This research focuses on developing a novel ultra high molecular weight polyethylene (UHMWPE) material reinforced with titanium dioxide (TiO ${}_2$ ) nanoparticles for producing craniofacial prostheses via an incremental sheet forming process (SPIF). First, UHMWPE-TiO ${}_2$ nanocomposite sheets were produced using incipient wetting and the compression molding process by considering different concentrations of TiO ${}_2$ nanoparticles. Then, the influence that the compression molding fabrication process has on the crystallinity and structural properties of the produced sample sheets was investigated. Experimental characterizations via scanning electron microscopy (SEM), differential scanning calorimetry (DSC), X-ray diffraction (XRD), Fourier transform infrared (FT-IR), tensile mechanical testing, and live/dead cell viability assays provided data that show an enhancement of the physical, mechanical, and biological properties. Finally, modifications on the nanocomposite material properties due to the SPIF manufacturing processes of a craniofacial prosthesis are addressed.

This paper focuses on reporting results obtained by the spark plasma sintering (SPS) consolidation and characterization of aluminum-based nanocomposites reinforced with concentrations of 0.5 wt%, 1 wt% and 2 wt% of single-walled carbon nanotubes (SWCNTs) and multi-walled carbon nanotubes (MWCNTs). Experimental characterization performed by SEM shows uniform carbon nanotube (CNT) dispersion as well as carbon clusters located in the grain boundary of the Al matrix. The structural analysis and crystallite size calculation were performed by X-ray diffraction tests, detecting the characteristic CNT diffraction peak only for the composites reinforced with MWCNTs. Furthermore, a considerable increment in the crystallite size value for those Al samples reinforced and sintered with 1 wt% of CNTs was observed. Hardness tests show an improvement in the composite surface hardness of about 11% and 18% for those samples reinforced with 2 wt% of SWNCTs and MWCNTs, respectively. Conductivity measurements show that the Al samples reinforced with 2 wt% of MWCNTs and with 0.5 wt% SWCNTs reach the highest IACS values of 50% and 34%, respectively.

Liposomes are employed for the delivery of molecular cargo in several classes of systems. For instance, the embedding of loaded liposomes in polymeric fibrous scaffolds has enabled the creation of hybrid materials that mimic biological membranes. Liposomes with unmodified surfaces have been predominantly integrated into fibers, which leads to instabilities due to interfacial incompatibility. In addition, electrospinning has been almost exclusively employed for fiber fabrication, which limits the potential for scale-up production. Here, we present the fabrication of hybrid biomimetic materials by fusing polymer-coated liposomes to force-spun microfibers to increase the stability of the hybrid materials and enhance the sustained release of the cargo. L-α-Phosphatidylcholine liposomes were coated with chitosan or polyethylene glycol (PEG). The nano-differential scanning calorimetry results confirm that polymer coating does not affect the phase transition temperature (T_m) of the liposomes, where only the model drug, quercetin, reduced T_m. Centrifugal spinning was employed to fabricate hydrophobic polycaprolactone (PCL) microfibers at various polymer concentrations and using various solvents and spinning parameters to increase the yield at the lowest fiber diameter. The highest microfiber production rate obtained occurred at a 20% (w/v) PCL concentration in 50 : 50 (v/v) chloroform and methanol solution with an average fiber diameter of 584.85 ± 26.30 nm. The non-chemical fusion of the polymer-coated liposomes and the fibrous scaffolds was promoted by immersion at T > T_m, under ultrasonication. We hypothesize that the fusion is driven by hydrophobic interactions between the liposomes and the fibers, which merge the materials through the lipid bilayer. The fused hybrid material solved the burst release problem observed when adhering plain liposomes to nanofibers. Both PEG and chitosan yielded a sustained release, where the release rate with the former was faster. These results demonstrate that the fusion of polymer-coated liposomes and microfibers enables more effective blending of the loaded carriers into the polymer microfibers. Ultimately, the fused liposome/microfiber hybrids are stable matrices and enhance the sustained release of molecular cargo.

This article focuses on exploring how the electrical conductivity and densification properties of metallic samples made from aluminum (Al) powders reinforced with 0.5 wt % concentration of multi-walled carbon nanotubes (MWCNTs) and consolidated through spark plasma sintering (SPS) process are affected by the carbon nanotubes dispersion and the Al particles morphology. Experimental characterization tests performed by scanning electron microscopy (SEM) and by energy dispersive spectroscopy (EDS) show that the MWCNTs were uniformly ball-milled and dispersed in the Al surface particles, and undesirable phases were not observed in X-ray diffraction measurements. Furthermore, high densification parts and an improvement of about 40% in the electrical conductivity values were confirmed via experimental tests performed on the produced sintered samples. These results elucidate that modifying the powder morphology using the ball-milling technique to bond carbon nanotubes into the Al surface particles aids the ability to obtain highly dense parts with increasing electrical conductivity properties.