Background: Effective hypertrophy-oriented resistance training (RT) should comprise a combination of mechanical tension and metabolic stress. Regarding training variables, the most effective values are widely described in the literature. However, there is still a lack of consensus regarding the efficiency of advanced RT techniques and methods in comparison to traditional approaches. Methods: MEDLINE and SPORTDiscus databases were searched from 1996 to September 2019 for all studies investigating the effects of advanced RT techniques and methods on muscle hypertrophy and training variables. Thirty articles met the inclusion criteria and were consequently included for the quality assessment and data extraction. Results: Concerning the time-efficiency of training, the use of agonist–antagonist, upper–lower body supersets, drop and cluster sets, sarcoplasma stimulating training, employment of fast, but controlled duration of eccentric contractions (~2s), and high-load RT supplemented with low-load RT under blood flow restriction may provide an additional stimulus and an advantage to traditional training protocols. With regard to the higher degree of mechanical tension, the use of accentuated eccentric loading in RT should be considered. Implementation of drop sets, sarcoplasma stimulating training, low-load RT in conjunction with low-load RT under blood flow restriction could provide time-efficient solutions to increased metabolic stress. Conclusions: Due to insufficient evidence, it is difficult to provide specific guidelines for volume, intensity of effort, and frequency of previously mentioned RT techniques and methods. However, well-trained athletes may integrate advanced RT techniques and methods into their routines as an additional stimulus to break through plateaus and to prevent training monotony.

The aim of this study was to investigate the relationship between linear sprint, power output obtained during a squat and change of direction (COD) performance. Fifteen elite soccer players participated in this study (age = 21.7 ± 0.72 years, body mass = 74.9 ± 9.11 kg, body height = 180.4 ± 7 cm, training experience = 9 ± 1.5 years). To examine these correlations a following battery of tests were carried out: 20-m linear sprint, one-repetition maximum (1RM) squat strength, peak power output obtained during a squat at 50% 1RM and time obtained in two 20-m COD tests with different angles of direction change (90° and 135°). In addition, COD deficits (90°-COD_DEF and 135°-COD_DEF) for both COD tests were calculated. The Spearman’s rank order correlation showed a nearly perfect statistical relationship between the 90°-COD and the 90°-COD_DEF (r = 0.9; p < 0.001). In the case of 90°-COD_DEF, there was a large statistical relationship with 135°-COD_DEF (r = 0.59; p = 0.021). Moreover, there was a nearly perfect statistical relationship between 135°-COD and 135°-COD_DEF (r = 0.91; p < 0.001). The statistically insignificant (p > 0.05) relationship between 20-m linear sprint time, power output obtained during a squat at 50% 1RM, 1RM squat strength level and both COD test, as well as both COD deficits were found. Results of the present study showed that 20-m linear sprinting speed, 1RM squat strength, power output obtained during squat at 50% 1RM and COD ability at 90° and 135° angles, are separate physical qualities. Moreover, it seems that COD deficit provides a more isolated measure of COD ability than the COD tests alone and does not must be limited to a specific angle, but provides knowledge about the COD ability in a range of other angles, at least concerning 90° and 135° COD angles.

This study aimed to analyze acute changes in the muscle mechanical properties of the triceps brachii long head after bench press exercise performed at different external loads and with different intensities of effort along with power performance. Ten resistance-trained males (age: 27.7 ± 3.7 yr, body mass: 90.1 ± 17.1 kg, height: 184 ± 4 cm; experience in resistance training: 5.8 ± 2.6 yr, relative one-repetition maximum (1RM) in the bench press: 1.23 ± 0.22 kg/body mass) performed two different testing conditions in a randomized order. During the experimental session, participants performed four successive sets of two repetitions of the bench press exercise at: 50, 70, and 90% 1RM, respectively, followed by a set at 70% 1RM performed until failure, with a 4 min rest interval between each set. Immediately before and after each set, muscle mechanical properties of the dominant limb triceps brachii long head were assessed via a Myoton device. To determine fatigue, peak and average barbell velocity were measured at 70% 1RM and at 70% 1RM until failure (only first and second repetition). In the control condition, only muscle mechanical properties at the same time points after the warm-up were assessed. The intraclass correlation coefficients indicated “poor” to “excellent” reliability for decrement, relaxation time, and creep. Therefore, these variables were excluded from further analysis. Three-way ANOVAs (2 groups × 2 times × 4 loads) indicated a statistically significant group × time interaction for muscle tone (p = 0.008). Post hoc tests revealed a statistically significant increase in muscle tone after 70% 1RM (p = 0.034; ES = 0.32) and 90% 1RM (p = 0.011; ES = 0.56). No significant changes were found for stiffness. The t-tests indicated a significant decrease in peak (p = 0.001; ES = 1.02) and average barbell velocity (p = 0.008; ES = 0.8) during the first two repetitions of a set at 70% 1RM until failure in comparison to the set at 70% 1RM. The results indicate that low-volume, high-load resistance exercise immediately increases muscle tone but not stiffness. Despite no significant changes in the mechanical properties of the muscle being registered simultaneously with a decrease in barbell velocity, there was a trend of increased muscle tone. Therefore, further studies with larger samples are required to verify whether muscle tone could be a sensitive marker to detect acute muscle fatigue.

The aim of this study was to compare the muscle activity between the sling shot assisted (SS) and control (CONT) flat barbell bench press for selected external loads of 70%, 85%, 100% one-repetition maximum (1RM). Ten resistance-trained men participated in the study (age = 22.2 ± 1.9 years, body mass = 88.7 ± 11.2 kg, body height = 179.5 ± 4.1, 1RM in the bench press = 127.25 ± 25.86 kg, and strength training experience = 6 ± 2.5 years). Evaluation of peak muscle activity of the dominant body side was carried out using surface electromyography (sEMG) recorded for the triceps brachii, pectoralis major, and anterior deltoid during each attempt. The three-way repeated measure ANOVA revealed statistically significant main interaction for condition x muscle group (p < 0.01; η² = 0.569); load x muscle group (p < 0.01; η² = 0.709); and condition x load (p < 0.01; η² = 0.418). A main effect was also observed for condition (p < 0.01; η² = 0.968); load (p < 0.01; η² = 0.976); and muscle group (p < 0.01; η² = 0.977). The post hoc analysis for the main effect of the condition indicated statistically significant decrease in %MVIC for the SS compared to CONT condition (74.9 vs. 88.9%MVIC; p < 0.01; ES = 0.39). The results of this study showed that using the SS significantly affects the muscle activity pattern of the flat bench press and results in its acute decrease in comparison to an equal load under CONT conditions. The SS device may be an effective tool both in rehabilitation and strength training protocols by increasing stability with a reduction of muscular activity of the prime movers.