Conventional switch-mode LED drivers have problems such as poor performance in harmonic distortion, flickering, power factor correction, stresses on the switches, high switching losses, large size, and high cost. To resolve these problems, we propose a long-life LED driver with the ability of power factor correction. The proposed system is based on the integration of a half-bridge LLC resonant converter and two boundary-conducted boost converters. Both boost converters share a common inductor designed in such a way that both boost converters work in boundary conduction mode to attain the natural power factor correction. Half-bridge LLC resonant converter has soft switching characteristics, which assure the zero-voltage switching (ZVS) of primary-side switches and zero-current switching (ZCS) of diodes on the secondary side. This significantly reduces switching losses and improves the overall efficiency of the system. Voltage divider capacitors are used on the input side, which minimizes the bus voltages. The proposed system has two identical secondary windings with a coupled inductor to eliminate the mismatch between them, which powers two independent LED strings. The simulation of a 100-watt 240 V AC converter yields the approximate sinusoidal shape of the input current. It shows that the switches on the primary side are operated in ZVS and the diodes in ZCS. At 240-volt AC input, the efficiency is 87.4%, the total harmonics distortion (THD) is 10.98%, and the power factor (PF) is 0.98.
An output-capacitorless low-dropout regulator (LDO) with a push–pull buffer was presented in this paper. The proposed push–pull buffer was able to provide a large charge and discharge current to increase the slew rate at the gate of the power transistor effectively, thereby improving the transient response of this LDO. In addition, an adaptive resistance unit (ARU) was proposed to solve the right half-plane zero problem caused by Miller compensation to optimize the loop stability of the LDO. The proposed LDO was implemented in a 0.18-µm CMOS technology. Simulation results showed that the quiescent current of this LDO was only 16.1 µA. It regulated the output at 1.5 V from a 1.8 V supply, with a dropout voltage of 300 mV at the maximum output current of 50 mA. The maximum value of the voltage spike was 129 mV. Additionally, the recovery time of the LDO was 0.2 µs.
With the wide application of advanced portable devices, output-capacitorless low dropout regulators (OCL-LDO) are receiving increasing attention. This paper presents a low quiescent current OCL-LDO with fast transient response. A transient enhancement unit (TEU) is proposed as the output voltage-spike detection circuit. It enhances the transient response by improving the slew-rate at the gate of the power transistor. In addition, a current booster (CB), which consists of a current subtractor and a non-linear current mirror, is designed to improve the slew-rate further. The current subtractor increases the transconductances of the differential-input transistors to obtain a large slewing current, while the non-linear current mirror further boosts the current with no extra quiescent current consumption. The simulated results show that the proposed OCL-LDO is capable of supplying 100 mA load current while consuming 10.3 μA quiescent current. It regulates the output at 1 V from a supply voltage ranging from 1.2 to 1.8 V. When the load current is stepped from 1 mA to 100 mA in 100 ns, the OCL-LDO has attained a settling time of 190 ns, and the output voltage undershoot and overshoot are controlled under 110 mV.
This paper presents a charge pump circuit with a wide output range and low current mismatch applied to phase-locked loops. In this designed structure, T-shaped analog switches are adopted to suppress the non-ideal effects of clock feedthrough, switching time mismatch, and charge injection. A source follower and current splitting circuits are proposed to improve the matching accuracy of the charging and discharging currents and reduce the current mismatch rate. A rail-to-rail high-gain amplifier with a negative feedback connection is introduced to suppress the charge-sharing effect of the charge pump. A cascode current mirror with a high output impedance is used to provide the charge and discharge currents for the charge pump, which not only improves the current accuracy of the charge pump but also increases the output voltage range. The proposed charge pump is designed and simulated based on a 65 nm CMOS process. The results show that when the power supply voltage is 1.2 V, the output current of the charge pump is 100 μA, the output voltage is in the range of 0.2~1 V, and the maximum current mismatch rate and current variation rate are only 0.21% and 1.4%, respectively.
Low-dropout regulators, which have the capabilities of handling large output current and obtaining a superior transient response, are receiving increasing attention. This paper presents a high-output-current low-dropout regulator with high loop gain. An adaptive positive feedback compensation method is presented. It guarantees stability under full load conditions and achieves high loop gain. Without relying on an external zero, a ceramic capacitor with low equivalent series resistance can be employed, resulting in the minimized output voltage variation during the load transient response. In addition, the load regulation and line regulation are both small. An impedance adapting stage is inserted between the error amplifier and power transistor. It is suitable for low-supply voltage applications and drives the power transistor quickly. The simulation results indicate that the proposed LDO can supply a 1000 mA load current with a 200 mV dropout voltage. The load regulation and line regulations are 0.089 μV/mA and 0.562 m V/V, respectively. The power supply rejection is above 75 dB at 1 kHz under the full range of the output current.
In this paper, a novel super-junction trench silicon-on-insulator laterally-diffused metal-oxide-semiconductor (SJT SOI LDMOS) power device with additional hole leakage paths to improve single-event burnout (SEB) performance under high liner energy transfer (LET) is proposed for the first time. The electrical characteristics and SEB performance of the proposed SJT SOI LDMOS are both enhanced effectively. The replacement of a lightly doped N drift region with a heavily doped P pillar and N pillar considerably improves the tradeoff between breakdown voltage (BVDS) and specific on-resistance (Ron,sp). Compared with the conventional trench SOI LDMOS (CT SOI LDMOS), the static figures of merit (FOM, BVDS2/Ron,sp) of the SJT SOI LDMOS increases by 239%. The SEB performance of the SJT SOI LDMOS is significantly improved as the holes induced by the heavy ion can be quickly absorbed to the trench source metal through the heavily doped P+ region and P buried region rather than the base resistor of the parasitic bipolar junction transistor (BJT). The SEB threshold voltage (VSEB) of the CT SOI LDMOS is 58 V (39% of the BVDS) and that of the SJT SOI LDMOS is up to 173 V (87% of the BVDS) at high LET of 1 pC/μm.