With the aim of decreasing the number of experiments to obtain a perovskite solar cell (PSC) with maximum theoretical efficiency, in this paper, PSC performance was studied using the program solar cell capacitance simulator (SCAPS-1D). The PSC with the architecture ITO/TiO₂/perovskite/spiro-MeOTAD/Au was investigated, while the selected perovskite was mixed cation Rb_0.05Cs_0.1FA_0.85PbI₃. The analysis was based on an experimentally prepared solar cell with a power conversion efficiency of ~7%. The PSC performance, verified by short-circuit current density (J_sc), open-circuit voltage (V_oc), fill factor (FF) and power conversion efficiency (PCE), was studied by optimization of the simulation parameters responsible for improvement of the cell operation. The optimized parameters were absorber layer thickness, doping, defect concentration and the influence of the resistivity (the net effect of ohmic loss, R_s and the leakage current loss represented by the resistivity, R_shunt). The results of SCAPS-1D simulations estimated the theoretical power conversion efficiency of 15% for our material. We have showed that the main contribution to improvement of solar cell efficiency comes with lowering ohmic resistivity of the cell as well as doping and defect concentration, because their concentration is proportional to recombination rate.

Since the addition of BaTiO₃ in perovskite solar cells (PSCs) provides a more energetically favorable transport route for electrons, resulting in more efficient charge separation and electron extraction, in this work we experimentally prepared such a PSC and used a modeling approach to point out which simulation parameters have an influence on PSC characteristics and how they can be improved. We added a layer of BaTiO₃ onto the TiO₂ electron transport layer and prepared a PSC, which had an FTO/TiO₂/BaTiO₃/FAPbI₃/spiro-OMeTAD/Au architecture with a power conversion efficiency (PCE) of 11%. Further, we used the simulation program SCAPS-1D to investigate and optimize the device parameters (thickness of the BaTiO₃ and absorber layers, doping, and defect concentration) resulting in devices with PCEs reaching up to 15%, and even up to 20% if we assume an ideal structure with no interlayer defects. Our experimental findings and simulations in this paper highlight the promising interplay of multilayer TiO₂/BaTiO₃ ETLs for potential future applications in PSCs.

In this study, titanium dioxide nanotubes were prepared by electrochemical anodization technique and modified with an aqueous solution of FeCl₃ using hydrothermal synthesis method to control the amount and distribution of iron compounds on the anatase TiO₂ nanotubes. The objective was to synthesize immobilized FeOOH@TiO₂ or Fe₂O₃@TiO₂ photocatalysts designed for the flow-through reactor systems; to investigate thermal treatment effect on the photocatalytic efficiency; to determine appropriate Fe-compounds concentration for the maximum photocatalytic activity improvement, and to explain the mechanism responsible for the enhancement. The photocatalysts were tested for the degradation of 1H-benzotriazole in water under UV/solar light irradiation. Up to two times increase in the photocatalytic activity was obtained when TiO₂ nanotubes were modified with 0.8 mM Fe. At higher Fe concentrations (8 mM and 80 mM), the photocatalytic activity of the given photocatalysts decreased. To confirm the formation of FeOOH or Fe₂O₃ species, and to clarify the mechanism of photoactivity, X-ray diffraction (XRD), Raman spectroscopy (RS), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray spectroscopy (EDS) and UV-Vis spectroscopy were used.

In this paper, we studied the influence of polyvinylpyrrolidone (PVP) as a stabilization additive on optical and electrical properties of perovskite formamidinium lead iodide (FAPI) polycrystalline thin films on ZnO nanorods (ZNR). FAPI (as an active layer) was deposited from a single solution on ZNR (low temperature processed electron transport layer) using a one-step method with the inclusion of an anti-solvent. The role of PVP in the formation of the active layer was investigated by scanning electron microscopy and contact angle measurements to observe the effect on morphology, while X-ray diffraction was used as a method to study the stability of the film in an ambient environment. The effect of the PVP additive on the optical and electrical properties of the perovskite thin films was studied via photoluminescence, UV-Vis measurements, and electrical impedance spectroscopy. We have demonstrated that PVP inclusion in solution-processed perovskite FAPI thin films prevents the degradation of the film in an ambient atmosphere after aging for 2 months. The inclusion of the PVP also improves the infiltration of FAPI perovskite into ZnO nanostructures, increases electrical conductivity and radiative recombination of the photo-generated charge carriers. These results show promising information for promoting PVP stabilized FAPI perovskites for the new generation of photovoltaic devices.

In this paper, we emphasized the dual application of Cu-modified vertically aligned TiO₂ nanotube arrays as photocatalyst and a relative humidity sensor. The TiO₂ nanotube arrays were obtained by anodization of the titanium layer prepared using radio frequency magnetron sputtering (RFMS) and modified with different copper concentrations (0.5, 1, 1.5, and 2 M) by a wet-impregnation method. The sample modified with 2 M Cu(NO₃)₂ solution showed the highest efficiency for the NH₃ photocatalytic degradation and the most pronounced humidity response in comparison to the other studied samples. In order to investigate the structure and impact of Cu modification, X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS) were used. The photocatalytic activity and the kinetic study of ammonia oxidation were studied in a mini-photocatalytic wind tunnel reactor (MWPT), while relative humidity sensing was examined by impedance spectroscopy (IS). Higher NH₃ oxidation was a direct consequence of the increased generation of ^•OH radicals obtained by a more efficient photogenerated charge separation, which is correlated with the increase in the DC conductivity.

High-energy heavy ion irradiation is a very useful tool for the nanostructuring of 2D materials because defects can be introduced in a controlled way. This approach is especially attractive for the mass production of graphene nanomembranes when nanopore size and density can easily be tuned by ion irradiation parameters such as ion energy and applied fluence. Therefore, understanding the basic mechanisms in nanopore formation due to high-energy heavy ion impact is of the highest importance. In the present work, we used Raman spectroscopy to investigate the response of bilayer and trilayer graphene to this type of irradiation. Spectra obtained from graphene samples irradiated with 1.8 MeV I, 23 MeV I, 3 MeV Cu, 18 MeV Cu, and 12 MeV Si beams were analysed using the Lucchese model. It was found that the efficiency of damage production scales strongly with nuclear energy loss. Therefore, even for the most energetic 23 MeV I beam, the electronic energy loss does not contribute much to damage formation and ion tracks are unlikely to be formed.