Carlo Boaretti

Dr. Carlo Boaretti

Department of Industrial Engineering, University of Padua, 35122 Padua, Italy

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 March 2022 in Nanomaterials
Verified
Journal Article
Open access
PDF file
JIAYI YINJIAYI YIN
JIAYI YIN
Carlo BoarettiCarlo Boaretti
Carlo Boaretti
Alessandra LorenzettiAlessandra Lorenzetti
Alessandra Lorenzetti
Alessandro MartucciAlessandro Martucci
Alessandro Martucci
MRMartina Roso
Martina Roso
MMMichele Modesti
Michele Modesti
PVDF electrospun membranes were prepared by employing different mixtures of solvents and diverse electrospinning parameters. A comprehensive investigation was carried out, including morphology, nanofiber diameter, crystallinity, β-phase fraction, and piezoelectric response under external mechanical strain. It was demonstrated that by using low-toxicity DMSO as the solvent, PVDF membranes with good morphology (bead-free, smooth surface, and uniform nanofiber) can be obtained. All the fabricated membranes showed crystallinity and β-phase fraction above 48% and 80%, respectively; therefore, electrospinning is a good method for preparing PVDF membranes with the piezoelectric properties. Moreover, we considered a potential effect of the solvent properties and the electrospinning parameters on the final piezoelectric properties. When PVDF membranes with different β-phase fractions and crystallinity values are applied to make the piezoelectric transducers, various piezoelectric voltage outputs can be obtained. This paper provides an effective and efficient strategy for regulating the piezoelectric properties of PVDF electrospun membranes by controlling both solvent dipole moment and process parameters. To the best of our knowledge, this is the first time that the influence of a solvent’s dipole moment on the piezoelectric properties of electrospun materials has been reported.

27 January 2023 in ACS Omega
Verified
Journal Article
Open access
RDRiccardo Donadini
Riccardo Donadini
Carlo BoarettiCarlo Boaretti
Carlo Boaretti
ALAlessandra Lorenzetti
Alessandra Lorenzetti
MRMartina Roso
Martina Roso
DPDiego Penzo
Diego Penzo
MMMichele Modesti
Michele Modesti
In this work, we explored a microwave-assisted glycolysis process to chemically recycle rigid polyurethane (PU) foam waste to obtain a single-phase product with suitable physio-chemical properties as a secondary raw material for the preparation of new rigid PU products. Such an approach was compared to a conventionally heated (ConvH) process, analyzing the performances of different catalysts. The use of microwaves allowed a 94% decrease in the reaction time scale of rigid PU depolymerization, with a concurrent 45% reduction in energy expense. By using a PU/diethylene glycol mass ratio of 1.5, best performances were obtained with a 30 mmol/100gPU potassium acetate concentration, both in terms of the product viscosity and aromatic amine byproduct content. The glycolysis products recovered were employed in substitution to virgin polyol for rigid PU foam preparation, showing improved compressive strength and comparable thermal insulation properties up to a 30% content with respect to the traditional non-recycled counterpart.

23 December 2019 in Polymers
Verified
Journal Article
Open access
PDF file
ELEleonora Dal Lago
Eleonora Dal Lago
ECElisabetta Cagnin
Elisabetta Cagnin
Carlo BoarettiCarlo Boaretti
Carlo Boaretti
MRMartina Roso
Martina Roso
Alessandra LorenzettiAlessandra Lorenzetti
Alessandra Lorenzetti
MMMichele Modesti
Michele Modesti
The present work examines the influence of different carbon-based fillers on the performance of electrically conductive polymer blend composites. More specifically, we examined and compared the effects of graphene (GR), carbon nanotubes (CNTs) and carbon black (CB) on a PC/ABS matrix by morphological investigation, electrical and physic-mechanical characterization. Electrical analyses showed volume resistivity decreased when the CNTs and CB content were increased, although the use of melt-mixed GR did not really influence this property. For the latter, solution blending was found to be more suitable to obtain better GR dispersion, and it obtained electrical percolation with a graphene content ranging from 0.5% to 1% by weight, depending on the solvent removal method that was applied. There was a gradual improvement in all of the composites’ dielectric properties, in terms of loss factor, with temperature and the concentration of the filler. As expected, the use of rigid fillers increased the composite stiffness, which is reflected in a continuous increment in the composites’ modulus of elasticity. The improvements in tensile strength and modulus were coupled with a reduction in impact strength, indicating a decrease in polymer toughness and flexibility. TEM micrographs allowed us to confirm previous results from studies on filler dispersion. According to this study and the comparison of the three carbon-based fillers, CNTs are the best filler choice in terms of electrical and mechanical performance.

1 October 2018 in Polymer Degradation and Stability
Verified
Journal Article
Closed access
MMMichele Modesti
Michele Modesti
FCFrancesca Costantini
Francesca Costantini
ELEleonora Dal Lago
Eleonora Dal Lago
FPFrancesca Piovesan
Francesca Piovesan
MRMartina Roso
Martina Roso
Alessandra LorenzettiAlessandra Lorenzetti
Alessandra Lorenzetti

24 December 2018 in Materials
Verified
Journal Article
Open access
PDF file
ELEleonora Dal Lago
Eleonora Dal Lago
Carlo BoarettiCarlo Boaretti
Carlo Boaretti
FPFrancesca Piovesan
Francesca Piovesan
MRMartina Roso
Martina Roso
Alessandra LorenzettiAlessandra Lorenzetti
Alessandra Lorenzetti
MMMichele Modesti
Michele Modesti
The substitution of virgin resins by recycled ones is a worldwide tendency that is supported by the fluctuation of oil prices and the transition to a circular economy. Polymeric blends have been intensively studied because of their ability to provide tailored properties for particular applications. However, in their design phases, the issue of end-life re-use had not been well addressed, and now difficulties in their recycling are arising. In this study, we investigated the effect of three different compatibilizers: two chain extenders (CEs), (1) a styrene-acrylic oligomer (ESAo), and (2) methylene diphenyl diisocyanate (MDI) and an impact strength modifier, (3) an ethylene copolymer (EMAco), for the recycle of a post-industrial polycarbonate/polyethylene terephthalate (PC/PET) blend. The materials were prepared by reactive extrusion and characterized by intrinsic viscosity (IV) measurements, mechanical tests, differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy analysis (FTIR), and transmission electron microscopy (TEM). The introduction of each additive has been demonstrated to improve the compatibility between PET and PC in the post-industrial blend, leading to enhanced mechanical properties. The IV measurements increased to values that were comparable to the virgin material. In addition, CEs affected the crystallization of PET (as they reduced the degree of crystallinity), while EMAco acted as a nucleating agent. Morphological analysis enabled confirming the compatibilization effects induced by the tested additives.

20 November 2023 in Chemistry – A European Journal
Verified
Journal Article
Open access
RDRiccardo Donadini
Riccardo Donadini
Carlo BoarettiCarlo Boaretti
Carlo Boaretti
LSLuca Scopel
Luca Scopel
Alessandra LorenzettiAlessandra Lorenzetti
Alessandra Lorenzetti
MMMichele Modesti
Michele Modesti
Methylenedianiline (MDA) is a secondary, undesired, product of the glycolysis process of polyurethane (PU) scraps due to hydrolysis and pyrolysis side reactions. As an aromatic and carcinogen amine, MDA poses different problems in handling, transporting, and labelling recycled polyols derived from glycolysis, hindering the closure of PU recycling loop. Aiming to provide a solution to this issue, in this work different deaminating agents (DAs) were investigated with the purpose of analyzing their reactivity with MDA. A first part of the study was devoted to the analysis of MDA formation as a function of reaction time and catalyst concentration (potassium acetate) during glycolysis. It was observed that the amount of MDA increases almost linearly with the extent of PU depolymerization and catalyst content. Among the DAs analyzed 2‐ethylhexyl glycidyl ether (2‐EHGE), and acetic anhydride (Ac2O) showed interesting performance, which allowed MDA content to be diminished below the limit for labelling prescription in 30 minutes. PU rigid foams were, therefore, synthesized from the corresponding recycled products and characterized in terms of thermal and mechanical performance. Ac2O‐deaminated polyols led to structurally unstable foams with poor compressive strength, while 2‐EHGE‐deaminated products allowed the production of foams with improved mechanical performance and unaltered thermal conductivity.