The aim of study was to investigate the influence of kaolin on the physical properties and utility of film produced from native starch. The work involved measurements of strength, structure, and thermal properties. The films were prepared by the casting method. Composite films with 0%, 5%, 10%, and 15% kaolin additives were examined. Measurements of mechanical properties were carried out using the uniaxial tensile test, the nanoindentation test, and nanoscratching. Surface properties were examined by atomic force microscopy and contact angle measurements. Structure was determined by the X-ray diffraction method, and thermal properties were determined by differential scanning calorimetry. A significant influence of kaolin on the strength parameters and thermal and barrier properties of composite films was found. An increase in kaolin content reduced the tensile strength, Young’s modulus, and Poisson’s ratio. Structural analysis showed a partial intercalation and the layered arrangement of kaolin particles. Kaolin additives increased the barrier properties of water vapor in composite films of about 9%. Biopolymer modification by nanoclay reduced the thermal stability of composite films by 7% and could accelerate the biodegradation process. Increasing the concentration of kaolin in the biopolymer matrix led to heightened surface roughness (approximately 64%) and wettability of the surfaces of the film composites of 58%.

In the presented work the influence of different 3MgO·4SiO₂·H₂O (talc) contents in polypropylene samples on the structure, hardness, elasticity, and friction of the surface layer was investigated. The talc content ranged from 0 to 25 wt.%, and all the samples were obtained in the same conditions by the injection molding process. The analysis of the microstructure was performed by X-ray diffraction. Changes in the hardness and elasticity were determined for three different depths (300, 800, and 4000 nm) using an ultra nano tester. For the purpose of the examination of the friction properties of the obtained compounds, a nano-scratch tester was applied. Increasing the talc content caused growth in the indentation modulus and hardness values. Simultaneously, an effect of decreasing hardness and elastic modulus with increasing indentation depth was observed. The smallest effect size was observed for 25 wt.% talc content, which might suggest that talc addition increased the homogeneity of the observed composites. Scratch tests showed increasing scratch resistance along with increasing talc content for both constant and progressive loads. The growth in talc concentration led to a decrease in the degree of the polypropylene (PP) crystallinity of the surface layer. The exfoliation process occurred in PP composites.

Starch films modified with additives are materials increasingly being used in the production of packaging. These types of biopolymers can, to a considerable degree, replace plastic, contributing to the reduction in both production and waste management costs. However, they should be characterised by specific mechanical and surface parameters which determine their application. In the presented work, the PeakForce Quantitative Nanomechanics Mapping (PFQNM) method was applied to analyse a starch-based biopolymer modified with two different kaolin clay contents (5% and 10%). The technique used facilitates the assessment of the correlation of Atomic Force Microscope AFM height parameters with nanomechanical ones which provide the definitions of mutual interactions and allow the possibility to analyse materials in respect of various details. The investigated material was mapped in the Derjaguin–Muller–Toporov (DMT) modulus, adhesion and height domains. The results obtained indicated the impact of additives on the determined parameters. Increases in the DMT modulus and the adhesion force, along with the kaolin content, were observed. The enhancement of starch films with kaolin clay also induced growth in the surface roughness parameters.

In the present study, starch/powdered activated carbon composite films were prepared by incorporating various amounts of powdered activated carbon (PAC)—1–5, 10, and 15 %—into a starch matrix, using the solvent casting method. The effect of PAC addition on the biopolymer film was investigated. The mechanical properties were examined by ultra-nanoindentation, nanoscratch, and micro-tensile tests. Since the mechanical properties of biopolymer films are correlated with their structure, the effect of PAC addition was tested using X-ray diffraction. The surface parameters morphology and wettability were analyzed by atomic force microscopy (AFM) and contact angle measurements. The barrier properties were examined by determining water vapor permeability and the water solubility index. The obtained results did not show a monotonic dependence of the mechanical parameters on PAC content, with the exception of the maximum strain, which decreased as the amount of the additive increased. The visible effect of PAC addition was manifested in changes in the adhesive force value and in water vapor permeability (WVP). The barrier properties decreased with the increase of the filler content.

Antioxidant activity is one of the most desirable properties of natural compounds. Among these substances are phenolic compounds which exhibit excellent antiradical activity. The main aim of the present study was determination of the free radical scavenging activity of gruels with 5, 10 and 20% addition of linden inflorescence. The studies were based on two methods: TLC-bioautographic assay and spectrophotometric analysis using DPPH (2,2-diphenyl-1-picrylhydrazyl radical). The obtained results indicate that the radical scavenging properties of the extracts are positively correlated with the content of phenolic compounds in gruels and that a high-temperature extrusion process does not deactivate antioxidant polyphenolic compounds.