This work presents an efficient and high-sensitivity radio frequency (RF) energy harvesting supply. The harvester consists of a single-series circuit with one double diode on a low-cost, lossy FR-4 substrate, despite the fact that losses decrease RF harvesting efficiency. The design targeted minimum reflection coefficient and maximum rectification efficiency, taking into account not only the impedance matching network, but also the rectifier microstrip trace dimensions and the load. The simulated and measured rectenna efficiency was 28.4% for -20-dBm power input. In order to increase sensitivity, i.e., ability to harvest energy and operate at low power density, rectennas were connected in series configuration (voltage summing), forming rectenna arrays. The proposed RF harvesting system ability was tested at various input power levels, various sizes of rectenna arrays, with or without a commercial boost converter, allowing operation at RF power density as low as 0.0139 μW/cm 2 . It is emphasized that the boost converter, whenever used, was self-started, without any additional external energy. The system was tested in supplying a scatter radio sensor, showing experimentally the effect of input power density on the operational cold start duration and duty cycle of the sensor.
Nowadays, the monitoring of plant water stress is of high importance in smart agriculture. Instead of the traditional ground soil-moisture measurement, the leaf sensing is a new technology, which is used for the detection of plants needing water. In this paper, a novel, low-cost, and low-power system for leaf sensing using a new plant backscatter sensor node/tag is presented. The latter, can result in the prevention of water waste (water-use efficiency), when is connected to an irrigation system. Specifically, the sensor measures the temperature differential between the leaf and the air, which is directly related to the plant water stress. Next, the tag collects the information from the leaf sensor through an analog-to-digital converter, and then, communicates remotely with a low-cost software-defined radio reader using monostatic backscatter architecture. The tag consists of the sensor board, a microcontroller, an external timer, and an RF front-end for communication. The timer produces a subcarrier frequency for simultaneous access of multiple tags. The proposed work could be scaled and be a part of a large backscatter wireless sensor network. The communication protocol exploits the low-complexity Morse code modulation on a 868 MHz carrier signal. The presented novel proof-of-consent prototype is batteryless and was powered by a flexible solar panel consuming power around 20 μW. The performance was validated in an indoors environment where wireless communication was successfully achieved up to 2 m distance.
24 July 2012 in IEEE Transactions on Antennas and Propagation
We present a series of designs for uniplanar electromagnetic bandgap structures for antennas and microwave circuits. The proposed, easy to fabricate configurations, are based solely on metallic surfaces on layer interfaces, without the use of vias or other kinds of vertical connections. Their use in low profile antenna applications and mutual coupling reduction of planar radiating elements is investigated through an efficient and versatile technique, since the only information needed is the reflection phase and the dispersion diagram of the unit cell.
An intelligent reflecting surface (IRS) at terahertz (THz) bands is expected to have a massive number of reflecting elements to compensate for the severe propagation losses. However, as the IRS size grows, the conventional far-field assumption starts becoming invalid and the spherical wavefront of the radiated waves should be taken into account. In this work, we consider a spherical wave channel model and pursue a comprehensive study of IRS-aided multiple-input multiple-output (MIMO) in terms of power gain and energy efficiency (EE). Specifically, we first analyze the power gain under beamfocusing and beamforming, and show that the latter is suboptimal even for multiple meters away from the IRS. To this end, we derive an approximate, yet accurate, closed-form expression for the loss in the power gain under beamforming. Building on the derived model, we next show that an IRS can significantly improve the EE of MIMO when it operates in the radiating near-field and performs beamfocusing. Numerical results corroborate our analysis and provide novel insights into the design and performance of IRS-assisted THz communication.
A novel, polarization insensitive, wide-angle and broadband electromagnetic metamaterial absorber, which can cover either a flat or a bent geometry, is presented in this work. The periodic geometry has a unit-cell, which consists of four split ring resonators, which are sequentially rotated around the unit-cell axis progressively by 90 deg. First, the metallic parts of the geometry consists of low resistivity copper traces. Next, in order to increase the frequency bandwidth, resistively loaded traces, printed by conventional inkjet printer are used to replace the copper ones. For normal incidence, simulated and measurement results shown that the proposed flat absorber exhibits absorption efficiency higher than 0.8 for 6.9–29.9 GHz (i.e., bandwidth of 125%) regardless of polarization, while the curved absorber for 6.6–29 GHz (i.e., bandwidth of 126%) or for 10.5–29.6 GHz (i.e., bandwidth of 95%), depending the polarization. For oblique incidence and for TE or TM polarized incident wave it presents bandwidth of 118% (7.7–29.9 GHz) or 100.5% (9.9–29.9 GHz), respectively, for an incident angular range of 0–45 deg. Finally, the proposed absorber has thickness of 3.89 mm, corresponding to λ/11.7 at its lowest operation frequency.
19 August 2020 in IEEE Open Journal of the Communications Society
Electromagnetic wave control using the concept of a reflecting surface is first studied as a near-field and a far-field problem. Using a secondary source present in a wireless communication environment, such as a backscatter tag, it is possible to leverage the incoming radiation from the source as a reference-wave to synthesize the desired wavefront across the reflecting surface, radiating a field of interest. In this geometry, the phase grating, which is synthesized using an array of sub-wavelength unit cells, is calculated by interacting the incident reference-wave and the desired wavefront, similar to a hologram. When illuminated by the reference-wave, the reflected wavefront from the calculated phase grating is guaranteed to constructively add in the direction of the desired radiation (beam-steering in the far-field) and also focus at the intended depth (beam-focusing in the radiative near-field). Next, leveraging a dynamic modulation mechanism in the context of an intelligent reflective surface (IRS) illuminated by a backscatter tag, we demonstrate that one can selectively focus and defocus at an arbitrarily positioned receiver within the 3D field of view of the reflecting surface. This enables the control of the amplitude of the radiated electric field at the receiver location, paving the way for a spatial modulation mechanism by means of reconfiguring the reflecting surface in a backscattered wireless communication environment. In addition to the phase modification approach on a unit cell level to reconfigure the aperture radiated wavefronts, we finally present a time varying IRS concept making use of a time-delay based approach relying on a delay adjustment between the reflection coefficients of the IRS’ unit cell lattices.