The purpose of this paper is to present the course of a thermal cycle induced by welding in characteristic points in a joint and demonstrate the capabilities of simulation techniques with regard to thermal analysis of welding. Hybrid plasma-arc welding (HPAW) tests were conducted on samples of advanced high-strength steel (AHSS). Welding FEM analysis was carried out. Cooling time was determined for characteristic zones in the joint. The results of the simulation were then juxtaposed with the experimental data. Considerable diversification of the t8/5 and t8/3 times was observed for the analysed areas in the joint. The description of the thermal cycle presented in this paper questions the validity of analysing the changes occurring in the HAZ with the use of conventional TTT diagrams, extending the analysis of thermal conditions of a produced joint by new techniques of numerical prediction of thermal history of HPAW.
The aim of this article is to validate the method of conducting a multipoint temperature measurement in the area of welded joints as a tool for quality assessment of the joints in question. In order to establish a relationship between temperature readout at a given point, the value of heat input and the distance of the point form the weld axis, preliminary tests have been conducted on a set of padding welds. Correlation of measurement data analysis showed the high 0.99 level. In the second stage of the study, temperatures of joints welded with two different methods have been measured: the HPAW (Hybrid Plasma – Arc Welding) and classic SAW (Submerged Arc Welding) method. The obtained temperature curves reflect the intensity of heat input in a given welding process. When compared to thermal effects on metallographic specimens, the shapes of the curves show a potential for quality assessment of joints in production conditions. Estimating thermal effects with classic analytical methods proves imprecise with respect to advanced high-power welding processes. Monitoring temperature will allow to assess the quality of joints in the course of welding, which may be a remarkable factor in terms of limiting the HAZ (heat affected zone) tempering of joints made from MART steels (advanced high strength martensitic steel) – a phenomenon that exceedingly decreases the strength of the joints. The method for quality assessment of welded joints presented in this paper allows to extend the analysis of welding thermal conditions.
The paper consist of characterization of the essence of structure, properties and application of AlSi-SiC composite foams as well as limitations and possibilities of their joining. Porous structure with porosity up to 80% and exceptional properties of aluminium foams are the reason of their numerous application and interest of their joining. Consideration of methods of welding, soldering and gluing AlSi9-SiC10 composite foams, the joint structure, and properties. Recommendations for surface preparation of foam, and different joining procedures aimed at control the porosity of the foam and glued surface roughness were established. Result of EDS and XRD investigations of the AlSi9-SiC10 composite foams joint were considered.
The process of edge preparation for welding plays a crucial role in ensuring the quality of welded structures, affecting both their mechanical properties and overall economic efficiency. The aim of this article is to present a comparative analysis of traditional oxy-fuel cutting and modern milling methods for edge preparation of S355J2N low-alloy steel, focusing on surface quality, microstructural changes, as well as economic aspects. The study was conducted on plates with thicknesses ranging from 8 to 20 mm, using bevel angles of 30° and 45°. Both straight and curved beveled edges were investigated, utilizing a self-propelled OMCA 900 beveling machine, Gerima MMB 400B and SMA 60 BER milling machines, and a PERUN PC-211A/Y11 gas torch. Surface roughness measurements, macroscopic analysis of the edges, and HV1 microhardness testing were performed. Operation times were recorded to enable a cost analysis. The results demonstrated that milling significantly reduces edge roughness—Ra values decreased by a factor of 6 to 10 compared to oxy-fuel cutting. In the case of oxy-fuel cutting, a heat-affected zone approximately 2–3 mm thick and localized surface hardening up to 250–450 HV1 were observed, while milling did not cause changes in hardness. Cost analysis showed that under Polish labor rates, the total beveling costs were comparable for both methods (approximately 2 EUR/m), whereas under average EU labor rates, milling became the more economically viable solution.