With its low cost, high photocatalytic activity, high chemical stability and easy magnetic separation, Fe 3 O 4 @SiO 2 @TiO 2 –Co/rGO magnetic photocatalyst has a good application potential.
Efficient and reasonable utilization of waste biomass resources can not only avoid serious waste of material resources, but also solve the problem of environmental pollution. Therefore, the development of efficient and environmentally friendly waste biomass carbonization technology has important practical significance. Here, the activated carbon from orange peel (OAC) is prepared by potassium hydroxide (KOH) activation combined with high-temperature carbonization. The adsorption effects of OAC on three different pollutant aqueous solutions, methylene blue (MB), tetracycline (TC), and fluorescein sodium (NaFL), are examined. The OAC absorbent has excellent adsorption capacity for MB, TC, and NaFL pollutants of 10 mg L−1, with adsorption rates of 99.17%, 73.5%, and 94.24%, respectively. This study provides a new idea for turning waste biomass into treasure and eliminating the hidden danger of environmental pollution.
The development of non-precious metal catalysts with excellent bifunctional activities is significant for air–metal batteries. ABO3-type perovskite oxides can improve their catalytic activity and electronic conductivity by doping transition metal elements at B sites. Here, we develop a novel Sm0.5Sr0.5Co1−xNixO3−δ (SSCN) nanofiber-structured electrocatalyst. In 0.1 M KOH electrolyte solution, Sm0.5Sr0.5Co0.8Ni0.2O3−δ (SSCN82) with the optimal Co: Ni molar ratio exhibits good electrocatalytic activity for OER/ORR, affording a low onset potential of 1.39 V, a slight Tafel slope of 123.8 mV dec−1, and a current density of 6.01 mA cm−2 at 1.8 V, and the ORR reaction process was four-electron reaction pathway. Combining the morphological characteristic of SSCN nanofibers with the synergistic effect of cobalt and nickel with a suitable molar ratio is beneficial to improving the catalytic activity of SSCN perovskite oxides. SSCN82 exhibits good bi-functional catalytic performance and electrochemical double-layer capacitance.
11 February 2013 in Polymer-Plastics Technology and Engineering
A series of grafted ethylene-octene copolymers using itaconic acid (ITA) and styrene (St) as grafted monomers (POE-g-ITA, POE-g-(ITA-St)) were prepared via melt grafting technique by twin screw extrusion. The structure of grafted copolymer was characterized by FT-IR. The monomer and initiator concentration and the percent content of St in grafted monomers were also explored in the effect on the graft ratio (GR) and melt flow rate (MFR) of POE-g-ITA. The GR of POE-g-ITA reached 1.36% when when the ratio of POE:ITA:DCP is 94:6:0.36, and the GR of POE-g-(ITA-St) reached 1.44% when the ratio of POE:ITA:St:DCP = 94:3:3:0.18. The compatibilizer POE-g-ITA was introduced into PA6/POE blend by twin screw extrusion. The mechanical properties and morphological structure were investigated. The results revealed that the impact strength of the PA6/POE blend containing 5 phr of POE-g-ITA was enhanced 12.78 times compared with pure PA6. The crystallinity (Xc) of PA6 phase increased gradually when the compatibilizer POE-g-ITA was introduced into PA6/POE blends, although the melting point (Tm) of PA6 phase had no obvious change. The interface between PA6 and POE phase became indistinct and the compatibility was significantly increased.
A series of propylene-co-styrenic monomer copolymers were synthesized using the Friedel–Crafts alkylation reaction between chlorinated PP and substituted benzene, and the effects of these copolymers on a PP/PS (80/20) blend were investigated by using the impact test, morphology observation, thermo- and dynamic mechanical analysis, and rheology measurements. The results showed that the compatibilization efficiency varied as the variation of the substitute on the benzene ring of the styrenic monomer unit was incorporated in the PP chain in an order of methyl > ethyl > methoxyl. The copolymers bearing a crystalline isotactic polypropylene chain sequence and rubbery propylene-co-styrene-like unit chain segments may prepossess imaginable applications, giving an example for the synthesis and applications of PP-based copolymers, initiating a new way to broaden the polyolefin-based material family.
In this study, Fe 3 O 4 @TiO 2 –Ni core/shell particles linked to graphene oxide was fabricated via sol–gel and hydrothermal methods as a photocatalyst.