Brittleness is a crucial parameter of rock mass and the key indicator in rock engineerings, such as rockburst prediction, tunnelling machine borehole drilling, and hydraulic fracturing. To solve the problem of using present brittleness indexes, the existing rock brittleness indexes were firstly summarised in this paper. Then, a brittleness index ( ), which considers the ratio of stress drop rate and stress increase rate and the peak stress, was proposed. This new index has the advantage of simplifying the acquisition of key parameters and avoiding dimensional problems, as well as taking the complete stress-strain curves into account. While applying the , the peak strain is used to describe the difficulty of brittle failure before the peak point, and the ratio of stress drop to strain increase can reflect the stress drop rate without dimension problem. In order to verify the applicability of , through the PFC2D, the microparameters and confining pressure were changed to model different types of rock numerical specimens and different stress condition. The results show that the can well reflect and classify the brittleness characteristics of different rock types and characterise the constraint of confining pressure on rock brittleness. Moreover, the influence of microparameter on macroparameter was studied. In order to further verify the reliability of the brittleness index ( ), this study conducted uniaxial and triaxial compression tests (30 MPa) on marble, sandstone, limestone, and granite under different confining pressure.
Thermal conductivity is a critical parameter playing an important role in the heat transfer process in thermal engineering and enormous other engineering fields. Thus, the accurate acquisition of thermal conductivity has significant meaning for thermal engineering. However, compared to density test, moisture content test, and other physical property tests, the thermal conductivity is hard and expensive to acquire. Apparently, it has great meaning to accurately predict conductivity around a site through easily accessible parameters. In this paper, 40 samples are taken from 37 experimental points in Changchun, China, and the BPNN optimized by genetic algorithm (GA‐BPNN) is used to evaluate the thermal conductivity by moisture content, porosity, and natural density of undisturbed soil. The result is compared by two widely used empirical methods and BPNN method and shows that the GA‐BPNN has better prediction ability for soil thermal conductivity. The impact weight is obtained through mean impact value (MIV), where the natural density, moisture content, and porosity are 30.98%, 55.57%, and 13.45%, respectively. Due to high complexity of different parameter on thermal conductivity, some remolded soil specimens are taken to study the influence of individual factors on thermal conductivity. The correlations between moisture content and porosity with thermal conductivity are studied through control variable method. The result demonstrates that the impact weight of moisture content and porosity can be explained by remolded soil experiment to some extent.
With the rise of machine learning, a lot of excellent algorithms are used for settlement prediction. Backpropagation (BP) and Elman are two typical algorithms based on gradient descent, but their performance is greatly affected by the random selection of initial weights and thresholds, so this paper chooses Sparrow Search Algorithm (SSA) to build joint model. Then, two sets of land subsidence monitoring data generated during the excavation of a foundation pit in South China are used for analysis and verification. The results show that the optimization effect of SSA on the gradient descent model is remarkable and the stability of the model is improved to a certain extent. After that, SSA is compared with GA and PSO algorithms, and the comparison shows that SSA has higher optimization efficiency. Finally, select SSA-KELM, SSA-LSSVM and SSA-BP for further comparison and it proves that the optimization efficiency of SSA for BP is higher than other kind of neural network. At the same time, it also shows that the seven influencing factors selected in this paper are feasible as the input variables of the model, which is consistent with the conclusion drawn by the grey relational analysis.
The accumulation of municipal solid waste (MSW) in landfills often becomes a serious pollution source of geological environment and groundwater. The geological environment is the carrier of the landfill, and also the main pollution object of the landfill. The main pollution modes of the landfill site to the surrounding geological environment are purging, flushing, leachate, etc. If the leachate leakage cannot be found and repaired in time, it will cause serious harm to the geological environment and groundwater. The cost of geological environment and groundwater sampling through borehole surveys is high. Therefore, monitoring the seepage path and migration law of leachate is of great significance for determining the pollution range of the landfill site. In this study, by adjusting the grids of different sizes and changing the flow rate of leachate, the monitoring of fluid migration of different types of leachate was strengthened. The results show that the parallel potential monitoring method can quickly reflect the location and number of leachate points and the migration law of leachate. It provides effective reference data for landfill leachate monitoring.