Pretreatment is an essential process for the extensive utilization of lignocellulose materials. The effect of four common organic acid pretreatments for Kraft dissolving pulp production was comparatively investigated. It was found that under acidic conditions, hemicellulose can be effectively removed and more reducing sugars can be recovered. During acetic acid pretreatment, lignin that was dissolved in acetic acid could form a lignin-related film which would alleviate cellulose hydrolysis, while other organic acids caused severe cellulose degradation. Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and X-ray diffractometry (XRD) were used to characterize the pretreated chips in the process. Lignin droplets were attached to the surface of the treated wood chips according to the SEM results. The FTIR spectrum showed that the lignin peak signal becomes stronger, and the hemicellulose peak signal becomes weaker with acid pretreatment. The XRD spectrum demonstrated that the crystallinity index of the wood chips increased. The acetic acid pretreatment process-assisted Kraft process achieved higher yield (31.66%) and higher α-cellulose (98.28%) than any other organic acid pretreatment. Furthermore, extensive utilization of biomass was evaluated with the acetic acid pretreatment-assisted Kraft process. 43.8% polysaccharide (12.14% reducing sugar and 31.66% dissolving pulp) and 22.24% lignin (0.29% acetic acid lignin and 21.95% sulfate lignin) were recovered during the process. Biomass utilization could reach 66.04%. Acetic acid pretreatment is a promising process for extensive biomass utilization.
This chapter covers relative topics on wheat straw applied as fibrous raw materials for pulping and papermaking industry, i.e., chemical components and anatomy of wheat straw, pulping process and pulping properties, paper and paperboard products from wheat straw pulps, as well as environmental protection issues. Wheat straw is a kind of annual vascular-bundled herbal arthrophyte containing cellulose fibers that are acceptable for pulping and papermaking. The chemical components and anatomy of wheat straw were discussed; practically, soda or soda-AQ chemical pulping processes are common techniques often applied for chemical pulping from wheat straw, conventional and advanced bleaching sequences were introduced, and especially ECF and TCF bleaching techniques have been successfully applied in China’s paper mills. Cooking and black liquor extraction equipment and facilities are explained; chemi-mechanical pulping properties of wheat straw, corrugated medium, and linerboard products from wheat straw CMP pulps are evaluated; and chemical recovery from chemical cooking black liquor and effluent treatment processes are discussed. In this chapter, not only laboratory research results but also some commercial operation experiences are shared. These information and knowledge described in this chapter will help readers to have a good understanding about wheat straw pulping and papermaking; they are useful for pulping and papermaking engineer as reference for design and operation management of wheat straw pulping lines.
Silver nanowire (AgNW) has excellent thermal conductivity, which is an ideal material for fabricating flexible electrical heating materials. However, the poor stability of AgNWs is far from meeting the requirements for the practical application of electrical heating materials. Herein, by imitating the layered structure of nacre, the reduced graphene oxide (rGO)/AgNWs paper with a nacre-like structure was successfully prepared using a simple gravity-induced deposition approach. The obtained rGO/AgNWs paper showed excellent electrical conductivity (19.61 Ω/sq) and good pattern adjustability at the rGO to AgNWs ratio of 1:1. More importantly, the rGO/AgNWs paper exhibited high resistance to oxygen and water vapor, thus realizing long-term stability and reliability. Moreover, the design of a nacre-like structure could improve the thermal management performances of rGO/AgNWs paper, making it achieve a high Joule heating temperature (∼215.83°C) at low supplied voltages (3 V), the rapid response time (∼12 s) and long-term heating stability. These results indicate that the prepared rGO/AgNWs paper promises to be an electrical heating component with high chemical stability for thermal management electric materials.