THz waves have interesting applications in refractive index sensing. A THz gas sensor based on the guided Bloch surface wave resonance (GBSWR) in a one-dimensional photonic crystal (1DPhC), which consists of periodic polycarbonate (PC) layers and polyvinylidene fluoride (PVDF) layers, has been proposed. Numerical results based on finite element method (FEM) show that the photonic band gap that confines Bloch surface waves (BSWs) lies in the regime of 11.54 to 21.43 THz, in which THz wave can transmit in both PC and PVDF with the ignored absorption. The calculated sensitivity of hazardous gas HCN in angle is found to be 118.6°/RIU (and the corresponding figure of merit (FOM) is 227) and the sensitivity in frequency is 4.7 THz/RIU (the corresponding FOM is 301.3). The proposed structure may also be used for monitoring hazardous gases which show absorption to the incident THz wave. Further results show that for N2O gas, the maximum sensitivity goes up to 644 (transmittance unit/ one unit of the imaginary part of the refractive index). The proposed design may find applications in the detection of dangerous gases.
Simultaneous realization of high quality factor ( Q ), sensitivity, and figure of merit (FOM) play a pivotal role in building the THz sensor. For such purpose, we propose an all‐polymeric Bloch surface wave (BSW) structure that supports a bright BSW mode and a dark surface Fano state that is embedded in the continuum, both of which coupled to the same radiation channels. The existence of the sharp dip with a maximum depth of Fano line could be interpreted with the physics of Friedrich–Wintgen bound states in the continuum (FW‐BICs), because of the destructive interference between bright BSW and dark surface Fano modes. A strong angular‐ and frequency‐dependent Q was found. Related influential factors to Q value may also include an asymmetric arrangement of top and grating layers, together with the weak coupling provided by photonic crystals. One numerically optimized design shows a quality factor Q of the Fano mode as 23,670, which is almost two orders higher than that in conventional metallic‐metamaterial‐based designs. The optimized sensitivity can numerically reach 4.34 THz/RIU in the frequency domain, which is one order higher than that reported in all‐dielectric metasurfaces. We infer the high sensitivity is related to the phase‐matching condition provided by near‐subwavelength gratings. The associated FOM can reach 8857/RIU. Besides, the proposed design also numerically demonstrates high sensitivity in the angular domain ∼125.5°/RIU. Considering it poses no specific requirement for materials that own high contrast of permittivity in the THz regime, large interfacing area, the mechanical and chemical robustness offered by polymers and low cost in fabrication, such all‐polymeric BSW structure that supports novel Fano resonance in THz window may give access to rich applications in hazardous gas detection and label‐free bio‐sensing.
In recent findings, a new classification of 1D and 2D tetrahexagonal boron nitrides (th-BN) consisting of square and hexagonal rings has been documented. These materials exhibit impressive properties such as the tunable band gap, strong optical absorption, suitable sign-tunable Poisson's ratio, and high ideal strength, making them promising for applications in nano- and opto-electronic industries. Stimulated by these studies, we have designed a cage-based three-dimensional tetrahexagonal boron nitride (3D th-B6N6) structure, which demonstrates excellent thermal, dynamic, and mechanical stability, including exceptional cohesive and formation energies of 6.66 and -0.93 eV per atom. Unlike direct band gap 1D and 2D tetrahexagonal boron nitride semiconductors, the proposed 3D tetrahexagonal boron nitride exhibits an insulating nature, with a wide indirect band gap of 6.175 eV at the HSE06 level. Moreover, in contrast to the unequal chemical bonding and ultraviolet optical absorption observed in the 2D th-BN sheet, all B and N atoms form a fully sp3-hybridized bonded 3D th-B6N6 structure, with excellent terahertz light absorption in the range of 0.3-10 THz. Notably, it also exhibits a Debye temperature of 1304.55 K and substantial phonon inelastic scattering. Our study introduces the BN family with novel properties and potential applications.
We demonstrated zero-index (ZI) photonic crystal (PhC) waveguides (ZIWs) operating at the Dirac point embedded between photonic bandgap (PBG) claddings, which improved fast-light propagation characteristics in the terahertz (THz) regime. The cross-shaped silicon-based waveguide supports a Dirac-like cone at the Brillouin zone center, enabling zero-effective refractive index behavior. By including PBG cladding, extending from circular and triangular to perturbed configurations, our ZIWs efficiently improved mode confinement through strong mode coupling, confirmed by supercell band analysis that revealed two guided modes with distinct dispersion characteristics. Group velocity ( vg ), group index ( ng ) calculations of dispersion bands and delay time analysis demonstrated fast-light propagation near the ZI frequency. The highest value we achieved for vg is ~ 236 μm/ps, or about 0.79 times the speed of light in free space, which aligned well with the time delay analysis, and corresponding ng values can numerically reach 1.18, showing a promotion of group velocity of 47.4% to 78.7% for the ZIWs at the Dirac point compared with that of conventional PhC waveguides. Numerical simulations confirmed robust field confinement through the broadband transmission spectrum within the ZI region, particularly for geometrically perturbed PBG structures. Furthermore, the insertion loss and phase shift analyses confirmed its superior performance, showing minimal losses (~ 0.015 to 0.02 dB) and smooth dispersion control. These results describe the potential of ZIWs with tailored PBG environments for applications in ultrafast photonic signal transport, especially for meeting the increasing demands of high-speed connections between chips in artificial intelligence computer centers and for on-chip interconnects among different photonic integrated circuits.
The utilization of microwave radiation has gained increasing importance in various biological applications. However, a significant challenge remains in the interaction between the microwaves and the human skin, primarily due to the impedance mismatch. Recently, the employment of split-ring resonator (SRR) topologies has become increasingly prevalent for addressing such a problem. Despite this, most existing literatures lack a comprehensive understanding of the underlying mechanisms. In this study, we follow Babinet’s principle and numerically study the dispersion relations of a single-split-ring resonator (S-SRR) and its complementary topology, single-complementary-split-ring resonator (S-CSRR). We focus on conducting the impedance analysis, along with far-field and near-field excitation characterizations. The results indicate that S-CSRR ensures an improved impedance matching, thereby significantly enhancing microwave power flow within the bio-tissue. A 2 × 2 array of S-CSRR is experimentally examined for validation. We demonstrate that the S-CSRR array enhances the total specific absorption rate (SAR) of a deeply-implanted-tumor-phantom by a factor of 1.95. Our work may provide a broader understanding towards impedance matching, which may facilitate the design of more efficient diagnostic tools in bio-medical field.