Rosa Marat-Mendes

Prof. Rosa Marat-Mendes

Escola Superior Náutica Infante D. Henrique
orcid

Research Focus & Metrics

Academic Career Length

28Years (1999-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2016 in Theoretical and Applied Fracture Mechanics
Verified
Journal Article
Closed access
RBRicardo Baptista
Ricardo Baptista
AMA. Mendão
A. Mendão
FRF. Rodrigues
F. Rodrigues
CCelio Figueiredo-Pina
Celio Figueiredo-Pina
MGMafalda Guedes
Mafalda Guedes
Rosa Marat-MendesRosa Marat-Mendes
Rosa Marat-Mendes

1 January 2016 in Procedia Structural Integrity
Verified
Journal Article
Open access
RBRicardo Baptista
Ricardo Baptista
AMAna Mendão
Ana Mendão
MGMafalda Guedes
Mafalda Guedes
Rosa Marat-MendesRosa Marat-Mendes
Rosa Marat-Mendes
The current work studies the effect of the incorporation of different amounts of graphite filler on the mechanical properties of epoxy resin and of carbon fiber reinforced epoxy composites. Graphite-reinforced epoxy-matrix composites were prepared with graphite fractions ranging from 5 to 30 wt%. The carbon-fiber reinforced graphite/epoxy hybrids were prepared using a fixed amount of carbon fiber, and graphite incorporation in the epoxy of 7.5, 10 and 11.5 wt%. After cure the produced materials were submitted to tensile and to flexural three point bending tests. Examination of microstructural features and fracture surfaces were undertaken by optical microscopy and scanning electron microscopy. Increased graphite filler contents results in improved tensile modulus of the epoxy matrix. The 7.5, 10 and 11.5 wt%-graphite materials showed also an increase in the ultimate stress value with increasing filler. Introduction of reinforcement carbon fibers enhances tensile modulus. This increase is higher for the higher amounts of graphite filler in the matrix. This study shows that graphite/epoxy composites reinforced with carbon fiber present higher mechanical performance than conventional carbon fiber reinforced epoxy matrix composites

1 August 2010 in Composite Structures
Verified
Journal Article
Closed access
Rosa Marat-MendesRosa Marat-Mendes
Rosa Marat-Mendes
Manuel FreitasManuel Freitas
Manuel Freitas


1 August 1999 in Sensors and Actuators A: Physical
Verified
Journal Article
Closed access
Rosa Marat-MendesRosa Marat-Mendes
Rosa Marat-Mendes
CDCarlos J. Dias
Carlos J. Dias
JMJ.N Marat-Mendes
J.N Marat-Mendes

3 June 2012 in Journal of Composite Materials
Verified
Journal Article
Closed access
Rosa Marat-MendesRosa Marat-Mendes
Rosa Marat-Mendes
MFM de Freitas
M de Freitas
Unidirectional laminates of reinforced glass/epoxy composites UE400/ET443 were tested by the use of fracture mechanics tests. Mode I, Mode II, Mode III and Mixed-Mode I-II were, respectively, obtained from specimens submitted to double cantilever beam, end notch flexure, Edge Crack Torsion and mixed-mode bending tests. Two different loadings were applied to the edge crack torsion specimens: the original and the modified edge crack torsion test. Scanning electron microscopy, analytical and numerical analysis were used to identify and separate fractographic features and to establish the differences between the various modes of fracture. Scanning electron micrographs of fractured surfaces showed that the most predominant fractographic features in Mode I and Mode II are the large amount of fibre pull-out and the cusps markings, respectively. Mode III characterisation shows that some limited Mixed-Mode II-III appear in both ends of the edge crack torsion specimen on delamination initiation and growth, but a predominant Mode III delamination exists in the middle of the specimens.