Based on end-quenching experiments combined with conductivity, hardness testing, and microstructural characterization, the quenching sensitivity of the mechanical and corrosion properties of 7475 aluminum alloy was investigated. The study revealed that as the quenching rate decreased, both the mechanical properties and exfoliation corrosion resistance exhibited increased quenching sensitivity. With the quenching rate decreasing from 31.9 °C/s to 2.5 °C/s, the conductivity increased by 4.1%IACS, the hardness decreased by 31%, the exfoliation corrosion grade transitioned from EC to ED, and the maximum exfoliation corrosion depth increased from 237 μm to 508 μm. As the quenching rate decreased, the η phase sequentially precipitated at recrystallized grain boundaries (RGBs), E phase particles, and subgrain boundaries (SGBs), while the T phase primarily precipitated on E phase particles. Furthermore, the significant precipitation of η and T phases led to a notable reduction in the quantity of age-precipitated phases, an increase in their size, and poor coherency with the matrix, resulting in decreased mechanical properties and a higher quenching sensitivity of the mechanical performance. Meanwhile, with the reduction in quenching rate, the size and spacing of grain boundary precipitated phases increased, the Zn and Mg contents of grain boundary precipitated phases increased, and the Precipitation Free Zone (PFZ) widened, leading to decreased exfoliation corrosion resistance and higher quenching sensitivity of the exfoliation corrosion performance.

The microstructure and mechanical properties of cold-rolled Cu-2.7Be sheets under various annealing processes and conditions were investigated in this research. The increased beryllium content in the Cu-2.7Be alloy facilitates the formation of brittle secondary phases. Consequently, the study highlights the functionality of annealed Cu-2.7Be alloys as more favorable dynodes than the traditionally used Cu-2.0Be alloys. The mechanism of recrystallization used for the transformation of Cu-2.7Be alloys was that of continuous static recrystallization (cSRX). Moreover, the relationship between the orientation of the β phases and that of the surrounding Cu-matrix was determined to be (111)_α∥(110)_β and (011)_α∥(001)_β. The β phase has a body-centered cubic (bcc) structure with a = b = c = 0.281 nm. The β phase undergoes a morphology transformation from primitive lath-shaped β particles to quadrangle-shaped β particles during the annealing process. Such transformations could potentially have an effect on the mechanical properties of Cu-2.7Be sheets. There was a noticeable decline in the yield strength of the Cu-2.7Be after annealing, and the samples annealed at 770 °C for 15 min achieved the elongation with deep and uniform dimples caused by suitable β particle sizes, appropriate grain sizes, and the maximum volume fraction of ∑3 boundaries.

The influence of grain structure and quenching rates on the exfoliation corrosion (EXCO) susceptibility of 7085 alloy was studied using immersion tests, optical microscopy (OM), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and scanning transmission electron microscopy (STEM). The results show that as the cooling rate decreases from 1048 °C/min to 129 °C/min; the size of grain boundary precipitates (GBPs); the width of precipitate-free zones (PFZ); and the content of Zn, Mg, and Cu in GBPs rise, leading to an increase in EXCO depth and consequently higher EXCO susceptibility. Meanwhile, there is a linear relationship between the average corrosion depth and the logarithm of the cooling rate. Corrosion cracks initiate at the grain boundaries (GBs) and primarily propagate along the HAGBs. In the bar grain (BG) sample at lower cooling rates, crack propagation along the sub-grain boundaries (SGBs) was observed. Compared to equiaxed grain (EG) samples, the elongated grain samples exhibit larger GBPs, a wider PFZ, and minor compositional differences in the GBPs, resulting in higher EXCO susceptibility.