In this study, iron-rich mining residue (UGSO) was used as a support to prepare a new Ni-based catalyst via a solid-state reaction protocol. Ni-UGSO with different Ni weight percentages wt.% (5, 10, and 13) were tested for C2H4 dry reforming (DR) and catalytic cracking (CC) after activation with H2. The reactions were conducted in a differential fixed-bed reactor at 550–750 °C and standard atmospheric pressure, using 0.5 g of catalyst. Pure gases were fed at a molar ratio of C2H4/CO2 = 3 for the DR reaction and C2H4/Ar = 3 for the CC reaction. The flow rate is defined by a GHSV = 4800 mLSTP/h.gcat. The catalyst performance is evaluated by calculating the C2H4 conversion as well as carbon and H2 yields. All fresh, activated, and spent catalysts, as well as deposited carbon, were characterized by Brunauer–Emmett–Teller (BET), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDX), transmission electron microscopy (TEM), temperature programmed reduction (TPR), and thermogravimetric analysis (TGA). The results so far show that the highest carbon and H2 yields are obtained with Ni-UGSO 13% at 750 °C for the CC reaction and at 650 °C for the DR reaction. The deposited carbon was found to be filamentous and of various sizes (i.e., diameters and lengths). The analyses of the results show that iron is responsible for the growth of carbon nanofilaments (CNF) and nickel is responsible for the split of C–C bonds. In terms of conversion and yield efficiencies, the performance of the catalytic formulations tested is proven at least equivalent to other Ni-based catalyst performances described by the literature.
This work has the purpose of evaluating the removal of zinc from aqueous solutions using Algerian untreated bentonite clay as an adsorbent. The choice of using natural untreated clay is justified by the fact that it is both a low cost and friendly environmental adsorbent material. This local bentonite is a montmorillonite clay type with a relatively high cationic exchange capacity of 136.2 meq/100 g. Calcium is the main exchangeable cation. A granulometric analysis shows that 49.1% of the clay particles are submicronic. The zinc adsorption capacity of bentonite was studied in batch mode. A kinetic study shows a fast removal capacity and a highly influenced bentonite adsorption capacity by the operational parameters such as contact time, mass of adsorbent, metal concentration, pH, and temperature. Fifty percent of the Zinc was removed during the first 5 min and equilibrium is reached in 1 h. A maximal removal capacity is obtained for a bentonite concentration of 5 g L−1 and a zinc initial concentration of 100 mg L−1. A pseudo-second-order kinetic model could be fitted to the experimental data. The equilibrium data could be fitted with a Langmuir isotherm equation. Depending on the negative value of ΔG, the adsorption of Zn2+ on SIG untreated bentonite surfaces was spontaneous and the adsorption was an endothermic process.
Les applications industrielles principales de la protection cathodique concernent les canalisations enterrées ou immergées. Le choix d’une méthode de protection contre la corrosion électrochimique se fait d’une part, selon le milieu environnant et d’autre part, selon les considérations économiques. La protection cathodique s’avère généralement peu coûteuse et efficace sur une longue durée lorsque cette technique est maitrisée et accompagnée d’une bonne connaissance des conditions environnantes. L’application de la technique de la protection cathodique a pour but de diminuer le potentiel de polarisation du métal à un niveau pour lequel la vitesse de corrosion du métal est réduite de façon significative. Le seuil de protection cathodique peut être déterminé thermodynamiquement et il correspond au seuil d’immunité. Deux types de systèmes de protection cathodiques sont couramment appliqués : Les systèmes de protection galvanique utilisent les anodes galvaniques, également appelées les anodes sacrificielles, qui sont électrochimiquement plus électronégatives que la structure à protéger et les systèmes à courant imposé, par le biais d’un générateur de courant qui débitera un courant continu de l’anode vers la structure à protéger. L’objet de cette étude est de dimensionner un système de protection cathodique d’un pipeline par soutirage de courant avec appoint électrique d’énergie solaire.