The combination of nanoparticles (NP) and surfactant has been intensively studied to improve the thermal stability and optimize the performance of foams. This study focuses on the influence of silica NPs with different concentration on the thermal stability of gel foams based on a mixture of fluorocarbon (FS-50) and hydrocarbon (APG0810) surfactants. The surface activity, conductivity, viscosity, and foaming ability of the APG0810/FS-50/NPs dispersions are characterized. The effects of NP concentration on coarsening, drainage, and decay, as well as of the gel foams under thermal action, are systematically studied. Results show that NP concentration has a significant effect on the molecular interactions of the APG0810/FS-50/NP dispersions. The surface tension and conductivity of the dispersions decrease but the viscosity increases with the increase in NP concentration. The foaming ability of APG0810/FS-50 solution is reduced by the addition of NPs and decreases with the increase in NP concentration. The coarsening, drainage, and decay of the gel foams under thermal action slow down significantly with increasing NP concentration. The thermal stability of the gel foams increases with the addition of NPs and further increases with the increase in NP concentration. This study provides a theoretical guidance for the application for gel foams containing NPs and surfactants in fire-extinguishing agents.
The foams stabilized by nanoparticles (NPs), water-soluble polymers, and surfactants have potential application prospects in the development of new, environmentally friendly firefighting foams. In the present study, a gel foam containing a water-soluble polymer (xanthan gum, XG), hydrophilic silica NPs, hydrocarbon surfactant (SDS), and fluorocarbon surfactant (FS-50) were prepared. The surface activity, conductivity, viscosity, and foaming ability of foam dispersions were characterized. The gel foam stability under a radiation heat source and temperature distribution in the vertical foam layer were evaluated systematically. The results show that the addition of NPs and XG has a significant effect on the foaming ability, viscosity and foam thermal stability, but has a very subtle effect on the conductivity and surface activity. The foaming ability of the FS-50/SDS solution was enhanced by the addition of NPs, but decreased with increasing the XG concentration. The thermal stability of the foams stabilized by SDS/FS-50/NPs/XG increased with the addition of NPs and increasing XG concentration. Foam drainage and coarsening were significantly decelerated by the addition of NPs and XG. The slower foam drainage and coarsening are the main reason for the intensified foam thermal stability. The results obtained from this study can provide guidance for developing new firefighting foams.
Pore structure has a significant influence on coal-bed methane (CBM) enhancement. Injecting liquid CO2 into coal seams is an effective way to increase CBM recovery. However, there has been insufficient research regarding the damage effects and fractal characteristics of pore structure at low temperature induced by injecting liquid CO2 into coal samples. Therefore, the methods of low-pressure nitrogen adsorption-desorption (LP-N2-Ad) and mercury intrusion porosimetry (MIP) were used to investigate the damage effects and fractal characteristics of pore structure with full aperture as the specimens were frozen by liquid CO2. The adsorption isotherms revealed that the tested coal samples belonged to type B, indicating that they contained many bottle and narrow-slit shaped pores. The average pore diameter (APD; average growth rate of 18.20%), specific surface area (SSA; average growth rate of 7.38%), and total pore volume (TPV; average growth rate of 18.26%) increased after the specimens were infiltrated by liquid CO2, which indicated the generation of new pores and the transformation of original pores. Fractal dimensions D1 (average of 2.58) and D2 (average of 2.90) of treated coal samples were both larger the raw coal (D1, average of 2.55 and D2, average of 2.87), which indicated that the treated specimens had more rough pore surfaces and complex internal pore structures than the raw coal samples. The seepage capacity was increased because D4 (average of 2.91) of the treated specimens was also higher than the raw specimens (D4, average of 2.86). The grey relational coefficient between the fractal dimension and pore structure parameters demonstrated that the SSA, APD, and porosity positively influenced the fractal features of the coal samples, whereas the TPV and permeability exerted negative influences.
This article applies nuclear magnetic resonance technology to the study of boron-containing traditional Chinese medicine, in order to explore the morphological evolution of boron elements in traditional Chinese medicine. Borax is a traditional Chinese medicine with anti-corrosion, anti-inflammatory, antibacterial, and anticonvulsant effects. It is made by boiling, removing stones, and drying borax minerals like borate salts. This article introduces an 11B nuclear magnetic resonance method for identifying and characterizing boron-containing compounds in TCM. We applied this technology to borax aqueous solutions in different chemical environments and found that with boron mixed in the form of SP2 hybridization in equilateral triangles and SP3 hybridization in equilateral tetrahedra, the pH changes in alkaline environments significantly affected the ratio of the two. At the same time, it was found that in addition to the raw material peak, boron signals of other boron-containing compounds were also detected in 20 commercially available boron-containing TCM preparations. These new boron-containing compounds may be true pharmaceutical active ingredients, and adding them directly to the formula can improve quality and safety. This article describes the detection of 11B NMR in boron-containing traditional Chinese medicine preparations. It is simple, non-destructive, and can provide chemical fingerprint studies for boron-containing traditional Chinese medicine.
Airtight blast door, as one of the key components of a rescue device or a ventilating device in underground coal mine, which can not only guarantee the normal operation ventilation system, but also can prevent the propagation of shock wave and invasion of toxic gases. Therefore, high structural stability and safety is fundamental when designing a door. An airtight blast door was developed and optimized based on static analysis and topological optimization, and dynamic response analysis of the optimized airtight blast door subjected to gas explosion load was conducted using a novel approach proposed in this paper-the FEM-SPH contact algorithm. Results showed that the main component weight of this kind of door is 27.4 % smaller than the original one without reducing the blast and impact behavior, the maximum displacement and stress of the optimization door obtained by FEM-SPH contact algorithm (dynamic response) are much larger than those using static mechanical analysis. The FEM-SPH contact algorithm and typical optimization method as well as the example presented in this paper are helpful for the original design and optimization of other products. Some conducive suggestions were recommended based on the simulation results.