The monitoring of particulate organic carbon (POC) flux at the bottom of the euphotic layer in global ocean using remote sensing satellite data plays an important role in clarifying and evaluating the ocean carbon cycle. Based on the in situ POC flux data, this paper evaluated various estimation models. The global ocean POC flux from 2003 to 2018 was calculated using the optimal model, and its temporal and spatial variation characteristics were analyzed. In general, the annual average of global ocean POC flux is about 8.5–14.3 ${\mathrm{Gt}\mathrm{C}\mathrm{yr}}^{-1}$ for period of 2003–2018. In the spatial dimension, the POC flux in the mid-latitude ocean (30–60°) is higher than that in the low-latitude (0–30°). The POC flux in Continental Margins with water depth less than 2000 m accounted for 30% of global ocean, which should receive more attention in global carbon cycle research. In the time dimension, the global POC flux decreases year by year generally, but the POC flux abnormally decreases during El Niño and increases during La Niña. In addition, due to global warming, sea ice melting, and bipolar sea area expansion, POC flux in high-latitude oceans (60–90°) is increasing year by year.

Remote sensing (RS)-derived vegetation indices (VIs) with medium and high spatial resolution have emerged as a promising dataset for fine-scale ecosystem modeling and agricultural monitoring at local or global scales. Before they can be used as reliable inputs for other research, conducting in situ measurements for validation is very critical. However, the spatial heterogeneity due to the diversity of land cover and its spatial organization in the landscape increases the uncertainty of validation, so design of optimal sampling is an important basis for the reliability of the validation. In this paper, we propose an integrative stratified sampling strategy (INTEG-STRAT) based on normalized difference vegetation index (NDVI) data as prior knowledge. The basic idea is to realize a sampling optimization by determining the optimal combination of the spatial sampling method (e.g., simple random sampling (SRS), spatial system sampling (SYS), stratified sampling, generalized random tessellation stratified (GRTS), balanced acceptance sampling (BAS)) and spatial stratification scheme with an objective rule. The objective rule in this paper is to minimize the root mean square error (RMSE) of 10-fold cross validation between estimated values (sample are not included) and the corresponding values on prior knowledge. Relative precision, correlation coefficient, and RMSE are used to compare the effectiveness of the proposed sampling strategy with each sampling method without considering sampling optimization. After comparing, we find that the INTEG-STRAT requires fewer samples to become stable and has higher accuracy. At site 1, when the correlation coefficient between NDVI image and the simulated NDVI surface reached 80%, INTEG-STRAT needed only 70 sampling points while other methods require more sampling points. At the same time, INTEG-STRAT strategy has a smaller RMSE between the estimated values and the corresponding values on prior knowledge image. In general, INTEG-STRAT is an effective method in the selection of representative samples to support the validation of vegetation indices products with medium and high spatial resolution.

Validation is an essential process to evaluate the quality of waterbody remote sensing products, and the reliability and effective application of the in situ data of waterbody parameters are an important part of validation. Based on the in situ data of chlorophyll-a (Chl-a), total suspended solids (TSS) and other environmental variables (EVs) measured at the fixed station in Taihu Lake, we attempt to develop a prediction model to determine whether the in situ measurement has enough representativeness for validating waterbody remote sensing products. Key EVs that affect the changes of Chl-a and TSS are firstly identified by using correlation analysis, which participate in modeling as variables. In addition, three multi-parameter modeling approaches are selected to simulate the daily changes of Chl-a and TSS under different EVs configurations. The results indicate that the highest prediction accuracy can be achieved through the generalized regression neural network (GRNN) based model. In the all-valid dataset, the testing absolute average relative errors (AEs) of GRNN-based Chl-a and TSS prediction model are 11.4% and 11.3%, respectively, and in the sunny-day dataset, the testing AEs are 8.6% and 8.2%, respectively. Meanwhile, the application example proves that the prediction model in this paper can be effectively used to screen the in situ data and determine the time window for satellite-ground data matching.

The airborne wide-angle staring synthetic aperture radar with the ground moving target indication (WasSAR-GMTI) can observe moving targets from multiple angles over extended periods. However, existing airborne WasSAR-GMTI methods exhibit the low accuracy and poor robustness in the three-dimensional (3D) trajectory reconstruction of moving targets. To address these issues, this paper has proposed a 3D trajectory reconstruction method of moving targets using the multi-channel airborne WasSAR based on the L -shaped antenna. The L -shaped antenna system consists of the along-track antenna and cross-track antenna subsystems. First, for the along-track subsystem, the clutter suppression interferometry (CSI) algorithm is applied to detect moving targets, which can extract motion parameters, mainly including the slant range, doppler center and along-track interferometric phase. These parameters are used to estimate the position of the moving target on the equivalent reference plane. Then, for the cross-track subsystem, the cross-track interferometric processing is applied to extract the cross-track phase at the same reference position. Finally, the slant range, doppler center, and cross-track phase are combined to estimate the 3D position of moving targets and then reconstruct their 3D motion trajectory. The proposed method is validated using both simulated and real WasSAR-GMTI data, and experimental results demonstrate that the proposed method has the good performance in the 3D trajectory reconstruction of moving targets.

Limited by meteorological conditions, airspace, complex terrain and other factors, airborne millimeter-wave InSAR will inevitably face the situation of no control point layout when acquiring terrain data in the difficult mapping areas in Southwest China, which increases the difficulty of subsequent data processing. Moreover, the layout of control points in difficult mapping areas consumes a lot of manpower and time, which is not suitable for large-scale high-precision topographic mapping. To solve these problems, this paper proposes an automatic extraction of tie-points and interferometric calibration technology based on tie-points. This technology develops the automatic extraction algorithm of tie-points based on SAR + SIFT + RANSAC to obtain evenly distributed tie-points of adjacent images, and uses the evenly distributed tie-points as real known points to recalibrate the interference parameters, then carries out elevation transfer and elevation inversion through the tie-points of overlapping areas, thus realizing high-precision mapping without control points for airborne millimeter-wave InSAR. This paper uses measured data to verify the technology, and compares it with the areas with control points and marking points. The comparison results of elevation accuracy prove the feasibility and effectiveness of this method. This paper also discusses the difficulties in the treatment of typical areas, such as water areas, urban areas and mountain areas, and gives reasonable solutions that have good engineering application value.

The efficient acquisition and processing of large-scale terrain data has always been a focal point in the field of photogrammetry. Particularly in complex mountainous regions characterized by clouds, terrain, and airspace environments, the window for data collection is extremely limited. This paper investigates the use of airborne millimeter-wave InSAR systems for efficient terrain mapping under such challenging conditions. The system’s potential for technical application is significant due to its minimal influence from cloud cover and its ability to acquire data in all-weather and all-day conditions. Focusing on the key factors in airborne InSAR data acquisition, this study explores advanced route planning and ground control measurement techniques. Leveraging radar observation geometry and global SRTM DEM data, we simulate layover and shadow effects to formulate an optimal flight path design. Additionally, the study examines methods to reduce synchronous ground control points in mountainous areas, thereby enhancing the rapid acquisition of terrain data. The results demonstrate that this approach not only significantly reduces field work and aviation costs but also ensures the accuracy of the mountain surface data generated by airborne millimeter-wave InSAR, offering substantial practical application value by reducing field work and aviation costs while maintaining data accuracy.