There is a wide distribution of weakly cemented argillaceous rock masses in areas where there are many coal mines, and their complex characteristics make them more difficult to support. This paper researches this type of rock and studies the slurry diffusion mechanism and grouting reinforcement characteristics of injected rock mass and their relationship with compaction and splitting grouting. The grouting mode is dominated by compaction and splitting. The rheological behavior of cement slurries with different concentrations used in split grouting was studied. The existing grouting equipment was improved, and grouting tests were performed on loose aggregates of weakly cemented primary rock in a certain size range. Subsequently, basic physical parameter determination tests, microscopic tests, and uniaxial tests were performed on grout, and the effects of grouting pressure, moisture content of standard samples, slurry water/cement ratio, and curing time on grouting reinforcement were analyzed. During the grouting process, the pattern of plasma pulse diffusion and reinforcement was summarized as three types: compaction, splitting, and microcracking. The failure modes of rock were summarized as shear failure, shear failure along the interface of the plasma, and splitting damage.

To study the mechanical properties of argillaceous weakly cemented rock under dynamic loading, a sample reconstituted and graded loading scheme is firstly designed, and then the reorganization rock sample is used as the research object. Using a Hopkinson pressure bar test, the responses of an argillaceous weakly cemented rock mass under different reorganization loads and different impact velocities is studied, and changes in specimen shape after impact are also analyzed. The study found that with increased of the recombination load, the amplitude of the transmitted wave increases. With increasing impact velocity, the rate of the increase in the incident wave amplitude is much larger than that of the transmission wave amplitude. The dynamic stress–strain curve can be divided into a compaction stage, an approximate linear elastic stage, a microcrack growth stage and a strain softening stage. The larger the reorganization load is, the less obvious the compression stage of the stress–strain curve is, and the greater the elastic modulus is. The peak strength and elastic modulus increase with increasing strain rate before 500 s⁻¹. When the reorganization load is increased, the deformation decreases, and its impact resistance increases. With increasing impact velocity, the deformation of the specimen increases.

Rock materials are often affected by water in underground engineering. In this study, the mechanical and failure characteristics of tuff under different moisture content were studied using laboratory tests. The moisture content variation of tuff was studied in water absorption tests, and the mechanical and failure characteristics of tuff under different moisture contents were studied through uniaxial compression tests with a Micro-II acoustic emission (AE) control acquisition system. The results showed that the moisture content of tuff increases rapidly at the initial stage of water absorption tests and stabilizes after 180 h of immersion. According to the results of uniaxial compression tests, both uniaxial compressive strength and elasticity modulus decreased with the increase in moisture content. The AE parameters analyses showed that, when the moisture content increased, the accumulated AE counts and energy gradually decreased, and the “quiet period” at the initial stage of uniaxial compression tests lasted longer, and the RA (rise time⁄amplitude)–AF (AE counts⁄duration) distribution and the failure characteristics verified that the failure patterns evolved from shear failure to tensile failure. Scanning electron microscopy was used to observe the morphology of the fracture surface and analyze the influence of moisture content on the fracture characteristics of the tuff at the mesoscopic level. The results of this research can be used as a basis for studying the influence of water on tuff.

Aiming at the large-scale nonlinear deformation of the roadway in Liangjia Coal Mine, Shandong Province, the mudstone of the 1602 working face is taken as the research object. A high-precision mudstone weathering test system integrating monitoring and control was developed, and the weathering tests of expanded mudstone were carried out at 10 °C, 20 °C, 30 °C and 40 °C. The results show that the hygroscopic curves of expanded mudstone demonstrate a nonlinear growth trend at different temperatures, and the influence of temperature on the hygroscopic curves is less than 20%. From the overall law, it can be roughly divided into three stages: the strong hygroscopic stage, the hygroscopic deceleration stage and the stable hygroscopic stage. The maximum expansion rates of the samples were 4.1%, 5.3%, 6.2% and 6.8%, respectively, and the water content and expansion rates corresponding to different ambient temperature and humidity were generally “concave”. The mechanical tests show that the mechanical properties of mudstone decrease as the ambient temperature increases, and the corresponding compressive strength decreases by 16~50%. The linear degradation is obvious, and the gradual expansion of peak strain indicates that the plasticity of the rock increases and the elastic modulus decreases linearly.

Short-term and creep tests of fractured sandstone with different degrees of damage prepared using pre-peak and post-peak unloading tests on intact sandstone were carried out using a servo-controlled rock mechanics system. Based on our experimental results, the influence of confining pressure and damage on short-term mechanical behavior of fractured sandstone with different degrees of damage was first analyzed. The results show that the peak strength, residual strength, elastic modulus, and secant modulus of fractured sandstone increase linearly with increasing confining pressure, but decrease with increasing damage. The short-term failure modes depend on the damage and change from typical shear failure modes to multiple shear failure modes with increasing damage. Then, the influence of the differential stress, confining pressure, and the degree of damage on the creep mechanical behavior of fractured specimens was further investigated. The axial instantaneous strain and creep strain increase linearly with increasing differential stress, and the specimens exhibit significant time-dependent behavior under high stress. The steady creep rate increases with increasing stress, but it decreases with increasing confining pressure and damage. However, the long-term strength and creep failure strength of fractured specimens increase linearly with increasing confining pressure, but they decrease linearly with increasing damage. The creep failure modes of fractured specimens are also the main shear failure modes, which are similar to the short-term failure modes.