A gross tonnage (GT) is a volume capacity of fishing vessel regarding its role in the fisheries resource utilization and management affairs. Information regarding GT is important, hence there is a need to conduct measurement in objective manner. The result of GT recalculation conducted by the Ministry of Transportation on under 30 GT fishing vessels showed that there is a significant difference between the documented GT and recalculated GT which indicates a massive mark down. Consequently, most of owners decline the later result as it goes higher and has impact on operational cost. Regarding that problem, this paper investigates the GT calculation process in Indonesia. In order to provide objective measurement, this research compares the existing GT calculation method and numerical computation. The result reveals that both methods produced different GT, which is about 32% gap for fishing vessels in Muncar and 27% gap in Prigi.Keywords: Gross tonnage, fishing boat, measurement, numerical computation
13 August 2020 in International Journal of Marine Engineering Innovation and Research
Propeller is similar to rotating fan blade with having primary function as propulsion system. In order to increase propeller performance, Engineer is developing Energy Saving Devices ( ESD ) to reduces operational cost, clean energy and for long term utilization. The global emmision from marine is 2.7 % in 2007. One of ESD is Propeller Boss Cap Fins ( PBCF ). The focus of this thesis is to design and developed PBCF B - series propeller. This thesis studies the performance of a propeller without and with PBCF such as efficiency, thrust, torsion and dynamic hub vortex phenomenon. To obtain the results this thesis uses Computational Fluid Dynamic (CFD). The PBCF simulations were based on its pitch angle. The simulation results shows that PBCF is achieved the highest efficiency which is 0.60 %, and increases thrust 3.21 %, and torsion increase 2.64 % compared to propeller without PBCF. It also shows that the PBCF is able to break the vortex flow and it will reduces the porosity to the rudder and decrese the corrosion potention to the rudder.
28 September 2019 in International Journal of Marine Engineering Innovation and Research
This paper provides analysis regarding a phenomenal hull shape called flat panel concept, the flat panel hull is an axe bow vessel at the front part and semi trimaran at the stern part. This concept is for a small vessel such as fishing vessels, patrol vessels and prototypes have been built. Resistance and motion is important part of a vessel design, this paper compares a flat plate vessel with 282.56 ton displacement with a conventional vessel with the same displacement and same speed. The resistance comparison was conducted using Computational Fluid Dynamic (CFD) on each ship with a speed range of 5-10 knots of operational speed. The resistance shows that the flat panel vessel generates higher resistance compared to the conventional vessel where the difference varies from 8.388% to 19.954% depending on the speed. It also found that the pitch motion (Ry) of flat panel vessel is positive that indicates the bow draft is lower during the simulation in calm water. The highest value of pitch is 1.13 degrees measured at the amidships or zero point or -0.3 m at the bow. Two While the relative velocity or flow analysis indicates that flow of the flat panel vessel has enormous turbulence flow around the stern hull and smoother flow pattern at the bow, this may cause the increase of resistance and bow diving in calm water phenomena. However since the most accurate test is based on model test in hydrodynamic laboratory, it is recommended to conduct the comparison experiment in hydrodynamic laboratory.
1 May 2020 in IOP Conference Series: Earth and Environmental Science
Fresh fish is known as one of the highly perishable foods. Losses in the primary fish harbor and seafood production are significant, with discarding rates between 9-15%, and more losses occur during fresh fish distribution. This research was an effort to provide better fresh fish distribution equipment using a refrigerator cooling system with Liquefied Petroleum Gas (LPG) fuel generator as a power source. LPG was chosen because it is more economical and profitable than gasoline. Based on fuel consumption, LPC was40.71% lower than premium gasoline, 62.63% lower than pertamax gasoline, and 64.85% lower than pertamax plus gasoline. The calculation of refrigeration heat load was carried out by applying heat transfer theory. Since the refrigeration heat load obtained was 310 Watt, then the type and capacity of the generator was easily determined.