Paranjayee Mandal

Dr. Paranjayee Mandal

Knowledge Exchange Associate
orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 July 2018 in Defect and Diffusion Forum
Verified
Journal Article
Closed access
PDF file
AGAres Gomez-Gallegos
Ares Gomez-Gallegos
Paranjayee MandalParanjayee Mandal
Paranjayee Mandal
DGDiego Gonzalez
Diego Gonzalez
NZNicola Zuelli
Nicola Zuelli
PBPaul Blackwell
Paul Blackwell
Since the development of the Ti54M titanium alloy in 2003, its application within the aerospace sector has gradually increased due to the combination of properties such as improved forgeability and machinability, low flow stress at elevated temperatures, and superplastic characteristics. However, for the successful exploitation of Ti54M a comprehensive understanding of its mechanical characteristics, microstructure stability, and superplastic behaviour is required. The superplastic forming of titanium alloys is characterised by high deformation at slow strain rates and high temperatures which influence the material microstructure, and in turn, determine the forming parameters. These mechanisms make the prediction of the material behaviour very challenging, limiting its application within the aerospace industry. Even though Ti54M has been commercially available for over 10 years, further studies of its mechanical and superplastic properties are still required with the aim of assessing its applicability within the aerospace industry as a replacement for other commercial titanium alloys. Therefore, in this work a study of the mechanical and superplastic properties of Ti54M, in comparison with other commercial titanium alloys used in the aerospace industry - i.e. Ti-6AL-4V, and Ti-6-2-4-2 - is presented. The final objective of this study, carried out at the Advanced Forming Research Centre (AFRC, University of Strathclyde, UK), is to obtain material data to calibrate and validate a model capable of estimating the behaviour and grain size evolution of titanium alloys at superplastic conditions.

1 March 2016 in Applied Surface Science
Verified
Journal Article
Closed access
Papken HovsepianPapken Hovsepian
Papken Hovsepian
Paranjayee MandalParanjayee Mandal
Paranjayee Mandal
AEArutiun Ehiasarian
Arutiun Ehiasarian
GSG. Sáfrán
G. Sáfrán
RTR. Tietema
R. Tietema
DDD. Doerwald
D. Doerwald

1 October 2019 in Journal of Manufacturing Processes
Verified
Journal Article
Closed access
Paranjayee MandalParanjayee Mandal
Paranjayee Mandal
HLHimanshu Lalvani
Himanshu Lalvani
MTMartin Tuffs
Martin Tuffs

1 September 2014 in Tribology International
Verified
Journal Article
Closed access
Paranjayee MandalParanjayee Mandal
Paranjayee Mandal
AEArutiun Ehiasarian
Arutiun Ehiasarian
Papken HovsepianPapken Hovsepian
Papken Hovsepian

1 August 2021 in Journal of Manufacturing Processes
Verified
Journal Article
Closed access
HLHimanshu Lalvani
Himanshu Lalvani
Paranjayee MandalParanjayee Mandal
Paranjayee Mandal

30 May 2020 in Metallurgical and Materials Transactions A
Verified
Journal Article
Open access
PDF file
CKChristiane Kienl
Christiane Kienl
Paranjayee MandalParanjayee Mandal
Paranjayee Mandal
HLHimanshu Lalvani
Himanshu Lalvani
CRCathie Rae
Cathie Rae
High-temperature compression tests were performed on a Ni-base superalloy with a multi-phase microstructure. Particular attention was given on the influence of the η phase on recrystallization of ATI 718Plus®. The compression tests were performed at two temperatures over a variety of strains and strain rates. Meta-dynamic recrystallization was studied by exposing the samples to a set dwell time at the test temperature after deformation. Electron backscatter diffraction (EBSD) was used to investigate the microstructures after the tests. Secondary electron imaging (SEI) and scanning transmission electron microscopy (STEM) were utilized in order to investigate the deformation behavior of η and obtaining a detailed understanding of the recrystallization mechanism. The secondary η phase was found to increase the recrystallized fraction compared to η free tests. However, clusters of thin lamellar η inhibited recrystallization. The flow curve softening was distinctly stronger in the microstructure containing precipitates. It could be shown by SE images that this was due to the breakage and realignment of η. In addition, η was also found to accommodate the stresses by a remarkable deformation without breaking up. This was considered to be due to the composite nature of the precipitate as well as the ongoing recrystallization in the surrounding matrix.