A promising strategy to improve the effectivity of anticancer treatment and decrease its side effects is to modulate drug release by using nanoparticulates (NPs) as carriers. In this study, methotrexate-loaded chitosan–polyanion nanoparticles were produced by polyelectrolyte complexation assisted by high-intensity sonication, using several anionic polymers, such as the sodium and potassium salts of poly(maleic acid-alt-ethylene) and poly(maleic acid-alt-octadecene), here named PAM-2 and PAM-18, respectively. Such NPs were analyzed and characterized according to particle size, polydispersity index, zeta potential and encapsulation efficiency. Likewise, their physical stability was tested at 4 °C and 40 °C in order to evaluate any change in the previously mentioned particle parameters. The in vitro methotrexate release was assessed at a pH of 7.4, which simulated physiological conditions, and the data were fitted to the heuristic models of order one, Higuchi, Peppas–Sahlin and Korsmeyer–Peppas. The results revealed that most of the MTX-chitosan–polyanion NPs have positive zeta potential values, sizes <280 nm and monodisperse populations, except for the NPs formed with PAM-18 polyanions. Further, the NPs showed adequate physical stability, preventing NP–NP aggregation. Likewise, these carriers modified the MTX release by an anomalous mechanism, where the NPs formed with PAM-2 polymer led to a release mechanism controlled by diffusion and relaxation, whereas the NPs formed with PAM-18 led to a mainly diffusion-controlled release mechanism.
Cancer is one of the most serious public health problems that affect humanity. Diverse delivery systems of anticancer drugs have been developed to enhance the treatment effectiveness and patient compliance. Thus, drug delivery systems from polymeric films could be an interesting and promising alternative, especially for skin chemotherapeutics. In this work, polymeric films based on glutathione-chitosan conjugates with degrees of thiolation of 4.4%, 5.1% and 7.0% were synthetized by casting-evaporation method and subsequent loading with methotrexate. The surface properties of these films were evaluated by contact angle and spreading rate measurements. The sessile drop methods along with the thermodynamic parameter of work of adhesion were determined using the Young–Dupré semi-empirical model. The in vitro methotrexate release was assessed at a pH of 4.5 and 7.4 simulating physiological conditions. Data from the resulting profiles were fitted to the order one, Higuchi, Peppas–Sahlin and Korsmeyer–Peppas kinetic models. The results suggest a strong relationship between the thiolation degree and hydrophilic surface properties such as contact angle and water spreading rate, whereas the work of adhesion was not significantly affected. Further, these polymer films could control the methotrexate release through diverse mechanisms such as diffusion and relaxation depending on the thiolation degree and the aqueous medium employed. In fact, as thiolation degree increased, the release mechanism shifted from a primary diffusional type towards a predominant relaxation-driven mechanism. These polymer films could be used as modified systems for anticancer local delivery.
Glutathione-chitosan conjugates are adequate carriers for anticancer treatment due to their ability for inhibition of efflux pumps, improved mucoadhesivity and in-situ gelling. These conjugates were obtained via carbodiimide at different reaction times in order to get different thiolation degrees (i.e., 4.4!, 5.1! and 7.0!) and their behavior in aqueous media at a pH of 4, 5 and 6 was assessed by measurements of hydrodynamic diameter, zeta potential and rheological analyses at a pH ranging from 4 to 6. Data examination was conducted by principal component analysis (PCA) which in turn explained 73.1! of data variability. All samples showed a Newtonian flow and thiolation rendered materials with a highly pronounced temperature-dependent behavior and a gel-like structure. In turn, the phase shift angle was the most prominent rheological change especially at a pH of 5.0 and 6.0 due to the formation of disulfide bonds. The thiolation degree was the most influential factor and it was inversely related to particle charge and consistency index.