A new 3D seismic reflection data volume acquired in 2012 has allowed for the detailed mapping and characterization of gas hydrate distribution in the Pearl River Mouth Basin in the South China Sea. Previous studies of core and logging data showed that gas hydrate occurrence at high concentrations is controlled by the presence of relatively coarse-grained sediment and the upward migration of thermogenic gas from the deeper sediment section into the overlying gas hydrate stability zone (BGHSZ); however, the spatial distribution of the gas hydrate remains poorly defined. We used a constrained sparse spike inversion technique to generate acoustic-impedance images of the hydrate-bearing sedimentary section from the newly acquired 3D seismic data volume. High-amplitude reflections just above the bottom-simulating reflectors (BSRs) were interpreted to be associated with the accumulation of gas hydrate with elevated saturations. Enhanced seismic reflections below the BSRs were interpreted to indicate the presence of free gas. The base of the BGHSZ was established using the occurrence of BSRs. In areas absent of well-developed BSRs, the BGHSZ was calculated from a model using the inverted P-wave velocity and subsurface temperature data. Seismic attributes were also extracted along the BGHSZ that indicate variations reservoir properties and inferred hydrocarbon accumulations at each site. Gas hydrate saturations estimated from the inversion of acoustic impedance of conventional 3D seismic data, along with well-log-derived rock-physics models were also used to estimate gas hydrate saturations. Our analysis determined that the gas hydrate petroleum system varies significantly across the Pearl River Mouth Basin and that variability in sedimentary properties as a product of depositional processes and the upward migration of gas from deeper thermogenic sources control the distribution of gas hydrates in this basin.

The Yap subduction zone is a distinctive erosive margin with an extremely slow convergence rate. The high relief of the subducting plate, generated by horst and graben structures and seamounts, leads to attenuation of the crust. In this study, we present the latest geophysical data, collected by the Chinese research vessel Kexue, to investigate subduction erosion at the Yap subduction zone and develop subduction models for Yap subduction zone structures. We show an anomalous distance between the Yap Trench and the adjacent volcanic arc, the steep slope of the trench arcward, a frontal prism, and rare sediment in the trench, all typical features of erosive margins. We propose that the high‐relief subducting plate has led to erosion of the overlying plate and that different subduction processes, controlled locally by the topography of the subducting plate, have modified the Yap subduction zone. Numerous normal faults increase the relief of the seafloor entering the trench, and an anomalously large slope angle along the trench reflects uplift of the fore‐arc high via seamount subduction. In addition, the thin crust of the subducted horst and graben structures, along with the normal faults, might have eroded the fore‐arc crust and subsequently eroded the Yap arc crust during subduction. These subduction erosional processes at the Yap Trench provide one of the best cases of an erosive margin in the world, particularly for a subduction zone with an extremely slow convergence rate.

Pore- and fracture-filling gas hydrates were identified from the core samples at several sites during the second Guangzhou Marine Geological Survey (GMGS2) expedition. Well logs indicated that gas hydrate occurred in three distinct layers at site GMGS2-08. The gas hydrate saturations calculated from well-log data and the seismic responses for the three gas hydrate-bearing layers, especially within the middle carbonate layer, were poorly known. We estimated gas hydrate saturations using isotropic and anisotropic models based on the mineral composition of the sediments and the effective medium theory. In the upper and lower gas hydrate-bearing layers, saturations estimated from anisotropic models are close to those estimated from pressures cores and chlorinity data. The average saturation using an anisotropic model in the upper (fracture-dominated) hydrate layer is approximately 10% with a maximum value of 25%. In the lower (fracture-dominated) layer, the horizontal and vertical gas hydrate-filled fractures and visible gas hydrate were formed with a maximum saturation of approximately 85%. For the middle layer, well logs show high P-wave velocity, density, high resistivity as well as low gamma ray, porosity, and drilling rate, together indicating a carbonate layer containing gas hydrate. The hydrate saturations calculated from isotropic models assuming hydrate formed at grain contacts are less than 20%, which fit well with two values calculated from chlorinity data for this layer. The upper gas hydrate layer shows no clear seismic response and probably consisted of small fractures filled with gas hydrate. The middle carbonate and lower fracture-filled gas hydrate-bearing layers show pull-up reflections, with the carbonate layer exhibiting relatively higher amplitudes. Pore-filling gas hydrate was also identified just above the depth of the bottom-simulating-reflector (BSR) from the GMGS2-05 drill site. Below the BSR, the push-down reflections, polarity reversal, and enhanced reflections indicate the occurrence of free gas in the study area.