Multivariate analysis (MA) is becoming a fundamental tool for processing in an efficient way the large amount of data collected in X-ray diffraction experiments. Multi-wedge data collections can increase the data quality in case of tiny protein crystals; in situ or operando setups allow investigating changes on powder samples occurring during repeated fast measurements; pump and probe experiments at X-ray free-electron laser (XFEL) sources supply structural characterization of fast photo-excitation processes. In all these cases, MA can facilitate the extraction of relevant information hidden in data, disclosing the possibility of automatic data processing even in absence of a priori structural knowledge. MA methods recently used in the field of X-ray diffraction are here reviewed and described, giving hints about theoretical background and possible applications. The use of MA in the framework of the modulated enhanced diffraction technique is described in detail.
Composite lightweight materials for X-ray shielding applications were studied and developed with the goal of replacing traditional screens made of lead and steel, with innovative materials with similar shielding properties, but lighter, more easily formed and workable, with lower impact on the environment and reduced toxicity for human health. New epoxy based composites additivated with barium sulfate and bismuth oxide were designed through simulations performed with softwares based on Geant4. Then, they were prepared and characterized using different techniques starting from digital radiography in order to test the radiopacity of the composites, in comparison with traditional materials. The lower environmental impact and toxicity of these innovative screens were quantified by Life Cycle Assessment (LCA) calculation based on the ecoinvent database, within the openLCA framework. Optimized mixtures are (i) 20% epoxy/60% bismuth oxide/20% barite, which guarantees the best performance in X-ray shielding, largely overcoming steel, but higher in costs and a weight reduction of circa 60%; (ii) 20% epoxy/40% bismuth oxide/40% barite which has slightly lower performances in shielding, but it is lighter and cheaper than the first one and (iii) the 20% epoxy/20% bismuth oxide/60% barite which is the cheapest material, still maintaining the X-ray shielding of steel. Depending on cost/efficiency request of the specific application (industrial radiography, aerospace, medical analysis), the final user can choose among the proposed solutions.
In materials and earth science, but also in chemistry, pharmaceutics and engineering, the quantification of elements and crystal phases in solid samples is often essential for a full characterization of materials. The most frequently used techniques for this purpose are X-ray fluorescence (XRF) for elemental analysis and X-ray powder diffraction (XRPD) for phase analysis. In both methods, relations between signal and quantity do exist but they are expressed in terms of complex equations including many parameters related to both sample and instruments, and the dependence on the active element or phase amounts to be determined is convoluted among those parameters. Often real-life samples hold relations not suitable for a direct quantification and, therefore, estimations based only on the values of the relative intensities are affected by large errors. Preferred orientation (PO) and microabsorption (MA) in XRPD cannot usually be avoided, and traditional corrections in Rietveld refinement, such as the Brindley MA correction, are not able, in general, to restore the correct phase quantification. In this work, a multivariate approach, where principal component analysis is exploited alone or combined with regression methods, is used on XRPD profiles collected on ad hoc designed mixtures to face and overcome the typical problems of traditional approaches. Moreover, the partial or no known crystal structure (PONKCS) method was tested on XRPD data, as an example of a hybrid approach between Rietveld and multivariate approaches, to correct for the MA effect. Particular attention is given to the comparison and selection of both method and pre-process, the two key steps for good performance when applying multivariate methods to obtain reliable quantitative estimations from XRPD data, especially when MA and PO are present. A similar approach was tested on XRF data to deal with matrix effects and compared with the more classical fundamental-parameter approach. Finally, useful indications to overcome the difficulties of the general user in managing the parameters for a successful application of multivariate approaches for XRPD and XRF data analysis are given.
New very fast and efficient detectors, installed both on laboratory instruments and synchrotron facilities, allow the monitoring of solid-state reactions from subsecond to minute scales with the production of large amounts of data. Traditional “one-by-one” pattern refinement needs complementary approaches, useful to handle hundreds to thousands of X-ray patterns. Principal-component analysis (PCA) has been applied to these fields in the last few years to speed up analysis with the specific goals of assessing data quality, identifying patterns where a reaction occurs, and extracting the kinetics. PCA is applied to the adsorption/desorption of Xe and CO2 within a Y zeolite. CO2 sequestration is a key issue in relation to climate change, while Xe is a critical raw material, and its purification is an important topic for the industry. At first, results were compared to traditional sequential Rietveld refinement. CO2-Y data were also compared with in situ single crystal data to investigate the different potentialities of PCA in the two cases. Two CO2 adsorption sites were confirmed, while three Xe sites were identified. CO2 showed a more linear adsorption trend with decreasing temperature, while Xe showed a more sigmoidal-like trend. Xe only showed site-dependent behavior in adsorption. Finally, PCA and correlation analysis, applied to analyze the parameters obtained from Rietveld refinement, highlighted finer details: in particular, this approach showed that the Y zeolite framework responded differently to CO2 and Xe adsorption.
The cocrystallization of active pharmaceutical ingredient naproxen with some acridines (acridine, 9-aminoacridine, 6,9-diamino-2-ethoxyacridine) has been explored and the conditions under which the crystallization can be carried out have been investigated. While the crystallization of acridine-based molecular crystals was widely studied under solution conditions, solvent-free and/or mechanochemical method potentialities are still unknown. To fill this gap, the cocrystallization of naproxen with the above-mentioned acridines was attempted using different approaches, e.g., by heat treatment of the dry mechanical mixture and by liquid-assisted grinding (LAG), as alternatives to the traditional precipitation by a proper solution. In the first case, the reaction is driven under dry conditions by the temperature and gave no results independently of the temperature used, below or above the melting point of the reactants. In the second case, the reaction is driven by the mechanical action of grinding assisted by a few drops of solvent to facilitate and improve the reaction. This screening allowed obtaining three new molecular crystals for naproxen coupled to acridine and a mono-aminoacridine and solved by single-crystal and powder X-ray diffraction (PXRD). Two host–guest structures were obtained by solution crystallization, while a layered structure was obtained under LAG conditions. Interconversion between molecular crystals formed by the same chemical species was hindered once a molecular crystal was obtained by a specific technique. Hirshfeld and energy framework calculations confirmed the remarkable structural differences between 1α and 1β packing and suggested that 1β is kinetically more stable. Variable-temperature PXRD, DSC and TGA were used to explore the stability of the compounds. 6,9-Diamino-2-ethoxyacridine proved to be too polar and/or too bulky to form crystals with naproxen regardless of the preparation method and the different stoichiometric ratios used. It is noteworthy that LAG allowed the preparation of the naproxen/acridine molecular crystal with a yield higher than 99% under almost solvent-free conditions. DSC indicated the formation of a eutectic between naproxen and acridine, with the possibility of recrystallizing the 1 : 1 complex also from the melt solution.