Altered pyroclastic (tephra) deposits are highly susceptible to landsliding, leading to fatalities and property damage every year. Halloysite, a low-activity clay mineral, is commonly associated with landslide-prone layers within altered tephra successions, especially in deposits with high sensitivity, which describes the post-failure strength loss. However, the precise role of halloysite in the development of sensitivity, and thus in sudden and unpredictable landsliding, is unknown. Here we show that an abundance of mushroom cap–shaped (MCS) spheroidal halloysite governs the development of sensitivity, and hence proneness to landsliding, in altered rhyolitic tephras, North Island, New Zealand. We found that a highly sensitive layer, which was involved in a flow slide, has a remarkably high content of aggregated MCS spheroids with substantial openings on one side. We suggest that short-range electrostatic and van der Waals interactions enabled the MCS spheroids to form interconnected aggregates by attraction between the edges of numerous paired silanol and aluminol sheets that are exposed in the openings and the convex silanol faces on the exterior surfaces of adjacent MCS spheroids. If these weak attractions are overcome during slope failure, multiple, weakly attracted MCS spheroids can be separated from one another, and the prevailing repulsion between exterior MCS surfaces results in a low remolded shear strength, a high sensitivity, and a high propensity for flow sliding. The evidence indicates that the attraction-detachment model explains the high sensitivity and contributes to an improved understanding of the mechanisms of flow sliding in sensitive, altered tephras rich in spheroidal halloysite.
3 August 2020 in Humanities and Social Sciences Communications
The comprehensive understanding of increasingly complex global challenges, such as climate change induced sea level rise demands for interdisciplinary research groups. As a result, there is an increasing interest of funding bodies to support interdisciplinary research initiatives. Attempts for interdisciplinary research in such programs often end in research between closely linked disciplines. This is often due to a lack of understanding about how to work interdisciplinarily as a group. Useful practical guidelines have been provided to overcome existing barriers during interdisciplinary integration. Working as an interdisciplinary research group becomes particularly challenging at the doctoral student level. This study reports findings of an interdisciplinary group project in which a group of doctoral students and postdoctoral researchers from various disciplines faced the challenges of reconciling natural, social, and legal aspects of a fictional coastal environmental problem. The research group went through three phases of interdisciplinary integration: (1) comparing disciplines, (2) understanding disciplines, and (3) thinking between disciplines. These phases finally resulted in the development of a practical guideline, including five concepts of interactive integration. A reflective analysis with observations made in existing literature about interdisciplinary integration further supported the feasibility of the practical guideline. It is intended that this practical guideline may help others to leave out pitfalls and to gain a more successful application of interdisciplinarity in their training.
11 March 2021 in Bulletin of Engineering Geology and the Environment
It is commonly assumed that dry and saturated sands exhibit similar cone resistance–relative density relationships. Some studies pointed out that partial saturation and calcareous sands with considerable fines content are potential factors affecting these relationships. However, there is experimental evidence in Shaqour Bull Eng Geol Environ 66:59-70, (2006) that clean uncemented quartz sand may exhibit lower cone resistance in saturated conditions. The present study aims on contributing towards better understanding the effect of water saturation on cone resistance in sand. For this purpose, Ticino sand samples were prepared dry and saturated in a calibration chamber and cone penetration tests were performed over a wide range of relative densities and at two consolidation stresses. Overall, it was observed that dry and saturated samples exhibited similar cone resistances. Only slightly higher cone resistances were observed for dry samples at the lower consolidation stress. Two anomalous samples, which were tested dry at medium relative density, were found to exhibit way higher cone resistances than expected from published cone resistance–relative density relationships. The Young's modulus was observed to be proportional to cone resistance and independent of whether a sample was tested dry or saturated, being therefore considered as more robust soil property for cone resistance relationships.
Weathered tephra is prevalent across volcanic islands like the North Island of New Zealand and is composed of volcanic airfall materials that have been subjected to various soil processes. Understanding their undrained response to cyclic loading is essential for geotechnical engineering applications in these regions because of frequently occurring local earthquakes. The authors describe for the first time the cyclic undrained behaviour of a weathered, clay-rich and highly sensitive tephra through triaxial tests. The weathered tephra experiences brittle failure and exhibits higher friction than sedimentary clays. Cyclic contour diagrams, covering the whole compressional and extensional range of stress conditions, are used to compare the cyclic shear strength of Pahoia tephra with those derived for sedimentary clays. It is found that weathered tephra: (a) is more resistant to small cyclic loading; (b) fails within a smaller range of cyclic shear stresses; and (c) exhibits a cyclic shear strength that peaks at zero average shear stress, in contrast to sedimentary clays where cyclic shear strength peaks at small compressive average stress.
1 August 2022 in International Journal of Geomechanics
The simulation of granular soil using advanced soil models relies on the precise determination of model parameters from laboratory or field experiments, or both. Although it is well known that sample reconstitution influences the stress–strain response of granular soil, the effect of different reconstitution methods on the calibration of advanced soil models has not been previously comprehensively addressed. In the present study, a hypoplastic model was calibrated from geotechnical laboratory tests on Cuxhaven sand samples. Triaxial tests were performed on samples having been reconstituted by three different methods: moist tamping, vacuum pluviation, and horizontal vibration. The influence of different reconstitution methods on the simulation performance of the hypoplastic model was quantified through three scenarios of increasing complexity: (1) stress–strain behavior in representative element volume (REV), that is, triaxial tests; (2) in situ plate load test (PLT); and (3) laboratory cone penetration test (CPT). The latter two are typical examples of boundary value problems with different strains and stiffnesses. The adopted reconstitution methods significantly affected the REV simulation at high relative density of both peak friction angles and peak dilation angles. The reconstitution methods have a limited effect on boundary value problem simulations, being moderate for PLTs and small for CPTs. The influence of stiffness (intergranular strain) parameters on simulation results increased from REVs (no influence detected), over boundary value problems with low strain and stiffness (PLTs) to boundary value problems with high strain and stiffness (CPTs).