Russell Farrugia

Dr. Russell Farrugia

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 February 2017 in Microsystem Technologies
Verified
Journal Article
Closed access
PDF file
RFRussell Farrugia
Russell Farrugia
IGIvan Grech
Ivan Grech
DCDuncan Camilleri
Duncan Camilleri
Owen CashaOwen Casha
Owen Casha
EGEdward Gatt
Edward Gatt
JMJoseph Micallef
Joseph Micallef

1 April 2019 in Microsystem Technologies
Verified
Journal Article
Closed access
PDF file
RFRussell Farrugia
Russell Farrugia
BPBarnaby Portelli
Barnaby Portelli
IGIvan Grech
Ivan Grech
DCDuncan Camilleri
Duncan Camilleri
OCOwen Casha
Owen Casha
EGEdward Gatt
Edward Gatt

26 December 2015 in Microsystem Technologies
Verified
Journal Article
Closed access
PDF file
RFRussell Farrugia
Russell Farrugia
IGIvan Grech
Ivan Grech
Owen CashaOwen Casha
Owen Casha
EGEdward Gatt
Edward Gatt
JMJoseph Micallef
Joseph Micallef
IBIngram Borg
Ingram Borg

18 May 2018 in Microsystem Technologies
Verified
Journal Article
Closed access
PDF file
RFRussell Farrugia
Russell Farrugia
IGIvan Grech
Ivan Grech
DCDuncan Camilleri
Duncan Camilleri
Owen CashaOwen Casha
Owen Casha
JMJoseph Micallef
Joseph Micallef
EGEdward Gatt
Edward Gatt

1 April 2015
Verified
Conference Paper
Closed access
RFRussell Farrugia
Russell Farrugia
IGIvan Grech
Ivan Grech
Owen CashaOwen Casha
Owen Casha
JMJoseph Micallef
Joseph Micallef
EGEdward Gatt
Edward Gatt
IBIngram Borg
Ingram Borg
Novel 3D packaging technologies which require large area mold embedding are being developed in order to achieve further minimization and cost reductions. Compression molding using epoxy molding compounds is one technique being considered for wafer-level encapsulation. However significant warpage in molded wafers is a critical issue which may hinder successive processes from being carried out. Cases of both symmetric (spherical) and asymmetric (cylindrical)-shaped warpage have been reported in wafer-level compression molding trials on blank wafers. This paper presents finite element models of the molded wafer, with and without embedded dies, which take into account the observed complex multi-state warpage characteristics. Molded wafer warpage measurements were carried out in order verify the applicability of the small and large deformation theories for layered plates, to deduce the cure shrinkage molding compound properties and to validate the finite element model of the molded blank wafer. The latter was used to analyze possible factors (nonplanar mold layer thickness, anisotropic wafer elastic properties) leading to asymmetric warpage. The numerical model will thus enable the prediction of the optimum process and material conditions for the warpage to be minimized together with the expected deformation of the molded wafer model with embedded dies.

1 April 2015
Verified
Conference Paper
Closed access
PDF file
RFRussell Farrugia
Russell Farrugia
IGIvan Grech
Ivan Grech
Owen CashaOwen Casha
Owen Casha
JMJoseph Micallef
Joseph Micallef
EGEdward Gatt
Edward Gatt
This paper presents an analysis, using finite element modelling, of a 40 MHz contour-mode RF MEMS resonator based on the SINTEF thin-film piezoelectric-onsubstrate (TPoS) fabrication technology. Novel simulation techniques are proposed which enable an exhaustive analysis of the relevant resonator characteristics including temperature drift and quality factor. This model also enables the analysis of possible tuning techniques which can be used to compensate for temperature and process-induced variations in the resonant frequency. The effect of the thickness ratio of the PZT film to the substrate on the resonant frequency and frequency shift is also discussed.