Solution-processed star-shaped triphenylamine (TPA) derivatives and dialkylated diketopyrrolopyrrole (DPP)-based small molecules have been widely studied because they both yield promising photon-to-electron conversion. However, the power conversion efficiency (PCE) of covalent star-shaped TPA-DPP derivatives is still very low. To design star-shaped TPA-DPP derivatives with better photovoltaic performance, we embedded a thiophene ring in between the TPA and DPP units, namely TPA-T-DPP, and reported the comparative studies of the optoelectronic and photovoltaic properties of TPA-DPP and TPA-T-DPP. Benefiting from the covalent thiophene bridges, compared to the TPA-DPP solid film, the TPA-T-DPP film showed enhanced light-harvesting ability, for instance, an improved absorptivity (Abs. = 1.72/100 nm vs. 1.23/100 nm), a broader absorption band (131 nm vs. 107 nm) and a narrower band gap (1.86 eV vs. 1.91 eV), from cyclic voltammetry. Studies on the photovoltaic properties revealed that the best TPA-T-DPP:PC71BM based device showed a dramatically enhanced PCE of 2.95%, increased by 2.14 times with respect to the efficiency of the best TPA-DPP based device (1.38%). The improvement of PCE also was observed in the small molecule:PC61BM based devices (1.81% vs. 1.13%). Test of the hole mobilites of the active layer provided further insight into the impact of the embedded thiophene units. The hole mobility of the TPA-T-DPP:PC71BM blended films was higher by about one order of magnitude (1.16 × 10−2 cm2 V−1 s−1) than that of the TPA-DPP:PC71BM blended films (3.85 × 10−3 cm2 V−1 s−1). These results clearly indicated that embedding the thiophene ring enlarged the conjugation, thus enhanced the light-harvesting ability and hole mobility, while further significantly improving the device performance. Additionally, TPA-T-DPP was also used as the electron-acceptor material, and the best P3HT:TPA-T-DPP based device exhibited a very high open-circuit voltage (1.14 V), which was among the highest values reported for single-layered OSC devices.
6 June 2013 in Physical Chemistry Chemical Physics
Because of their outstanding molecular optoelectronic properties, perylene diimides (PDIs) are promising alternatives to the commonly used PCBM. However, the overly strong aggregation ability, poor solution-processability and compatibility of PDIs severely limit their photovoltaic applications. We turned to borrowing the amphiphile concept to improve these supramolecular properties. Practically, we fine-tuned the molecular solvophobicity with respect to the molecular solvophilicity, e.g. Fsolvophob/solvophil, by changing the number of the weakly solvophobic 2-methoxyethoxyl (EG) groups in the bay-region of the thienyl-bridged dimeric PDI backbone, forming three PDI dimers of Bis-PDI-T (0 EG), Bis-PDI-T-EG (2 EG) and Bis-PDI-T-di-EG (4 EG) (Scheme 1). The photovoltaic properties using these dimers as the solution-processed non-fullerene electron-acceptor and P3HT as the electron-donor were investigated via the device configuration of ITO/PEDOT:PSS/P3HT:PDI dimer/Ca/Al. Bis-PDI-T exhibited overly strong aggregation ability and very poor solution-processability, which severely limited compatibility, giving a very poor power conversion efficiency (PCE) of 0.007%. When two EG groups were attached at the 1,1′-positions, the resulted Bis-PDI-T-EG showed dramatically reduced aggregation ability, improved solution-processability, compatibility and proper phase separation. Small sized phases (∼20 nm) dominated in the active layer and the best PCE was increased to 0.39%. When four solvophobic EG functions were introduced, affording Bis-PDI-T-di-EG with excellent supramolecular properties, particularly, the improvement of the phase separation with an increased phase size of 24 nm and the enhanced electron and hole mobilities, by 2–4 times, with respect to that of Bis-PDI-T-EG. The best PCE was further enhanced to 0.88%. After using 1-chloronaphthalene as the co-solvent of 1,2-dichlorobenzene to further improve the compatibility, the PCE was improved further up to 0.41% for Bis-PDI-T, 0.76% for Bis-PDI-T-EG and 1.54% for Bis-PDI-T-di-EG.
The field of organic solar cells (OSCs) has witnessed rapid progress in the last two years, due to the emergence of high-performance Y-series non-fullerene acceptors (NFAs). To further extend this family of the Y-series NFAs and tune their optoelectronic properties, herein, we developed a family of the Y-series NFAs (namely BTP-1V, BTP-2V, BTP-3V, and BTP-4V) by inserting vinylene π-bridges between the Y-series central fused core and non-halogenated end group IC. The incorporation of vinylene π-bridges can effectively reduce the bandgap of these NFAs with a significantly red-shifted absorption edge approaching 1020 nm. The optimized OSC device based on PBDB-T/BTP-1V demonstrated an excellent power conversion efficiency (PCE) of 11.03% with an open-circuit voltage (Voc) of 0.84 V, a short-circuit current density of 20.86 mA cm−2, a fill factor of 0.63, and an energy loss of 0.58 eV. It is worth noting that the PCE of over 11% is the highest value for binary single-junction OSCs based on the non-halogenated NFA with a bandgap below 1.28 eV. These results demonstrate that the vinylene π-bridges strategy strongly regulates the optoelectronic characteristics of NFAs, offering insights into the development of efficient OSCs based on ultra-narrow bandgap Y-series NFAs.