Incorporating BzMIMBF 4 layer into Me-4PACz (SAM) boosts the perovskite/HTL interface via strong π-conjugated heterojunctions, passivating perovskite defects and thus resulting in stable PSCs with a high PCE of up to 26.45%.
Bandgap energy is one of the most important properties for developing electronic devices because of its influence on the electrical conductivity of substances. Many methods have been developed to control bandgap, one of which is the realization of conducting polymers using narrow-bandgap polymers; however, the preparation of these polymers is complex. In this study, water-soluble, narrow-bandgap polymers with reactive groups were prepared by the addition–condensation reaction of pyrrole (Pyr), benzaldehyde-2-sulfonic acid sodium salt (BS), and aldehyde-containing reactive groups (aldehyde and pyridine) for post-crosslinking. Two types of reactions, aldehyde with p-phenylenediamine and pyridine with 1,2-dibromoethylene, were carried out for the π-conjugated post-crosslinking between polymers. The polymers were characterized by proton nuclear magnetic resonance (1H-NMR), thermogravimetric/differential thermal analysis (TG/DTA), UltraViolet-Visible-Near InfraRed spectroscopy (UV-Vis-NIR), and other analyses. The bandgaps of the polymers, calculated from their absorption, were less than 0.5 eV. Post-crosslinking prevents resolubility and develops electron-conducting routes between the polymer chains for π-conjugated systems. Moreover, the post-crosslinked polymers maintain their narrow bandgaps. The electrical conductivities of the as-prepared polymers were two orders of magnitude higher than those before the crosslinking.
Redox-active polymers have garnered significant attention as promising materials for redox capacitors, which are energy-storage devices that rely on reversible redox reactions to store and deliver electrical energy. Our focus was on optimizing the electrochemical performance in the design and synthesis of redox-active polymer electrodes. In this study, a redox-active polymer was prepared through step-by-step synthesis on a gold electrode. To achieve this, we designed an automatic sequential polymerization equipment that minimizes human intervention and enables a stepwise polymerization reaction. The electrochemical properties of the polymer gold electrodes were investigated. The degree of polymerization of the polymer grown on the gold electrode can be controlled by adjusting the cycle of the sequential operation. As the number of cycles increases, the amount of accumulated charge increases proportionally, indicating the potential for enhanced electrochemical performance.
Bandgap and energy levels are crucial for developing new electronic and photonic devices because photoabsorption is highly dependent on the bandgap. Moreover, the transfer of electrons and holes between different materials depends on their respective bandgaps and energy levels. In this study, we demonstrate the preparation of a series of water-soluble discontinuously π-conjugated polymers through the addition–condensation polymerization of pyrrole (Pyr), 1,2,3-trihydroxybenzene (THB) or 2,6-dihydroxytoluene (DHT), and aldehydes, including benzaldehyde-2-sulfonic acid sodium salt (BS) and 2,4,6-trihydroxybenzaldehyde (THBA). To control the energy levels of the polymers, varying amounts of phenols (THB or DHT) were introduced to alter the electronic properties of the polymer structure. The introduction of THB or DHT into the main chain results in discontinuous conjugation and enables the control of both the energy level and bandgap. Chemical modification (acetoxylation of phenols) of the polymers was employed to further tune the energy levels. The optical and electrochemical properties of the polymers were also investigated. The bandgaps of the polymers were controlled in the range of 0.5–1.95 eV, and their energy levels could also be effectively tuned.
In this study, water-soluble, narrow-band-gap polymers containing reactive groups were prepared by the addition-condensation of pyrrole (Pyr), benzaldehyde-2-sulfonic acid sodium salt (BS), and terephthalaldehydic acid (TPA) or p-hydroxybenzaldehyde (p-HB). TPA and p-HB were used for the post-crosslinking reaction between polymers. The polymers were characterized by employing various analyses such as 1H-NMR, thermal gravimetric analysis (TGA), and UV-Vis-NIR. The Eg values of polymers estimated from the absorption edges were 0.55 and 0.62 eV. The post-crosslinking reaction is important for preventing resolubilization and for developing an electron conducting route between the polymer chains. Herein, the post-crosslinked polymer was observed to maintain its narrow-band-gap and conductivity was increased 46 times compared to that observed before crosslinking.