TiC/316L stainless steel (316Lss) metal matrix composite parts have been formed using selective laser melting (SLM). In this study, we have investigated the influence of the TiC mass fraction on the microstructure evolution, microhardness, friction properties, wear properties, and corrosion resistance of the TiC/316Lss composites. The results show that the microhardness increased by the addition of the TiC mass fraction. In terms of friction and wear properties, the corrosion resistance initially increased, and then decreased. Compared with the pure 316Lss (298.3 HV0.2), the microhardness of the TiC/316Lss composites, which were formed with 2 wt% TiC, was raised to 335.2 HV0.2, which was a 12.4% increase, while the average friction coefficient was 0.123. The reason for this is that the addition of TiC can effectively refine the cell size, and as the TiC content increases, the refinement effect is more obvious. During the melting process, TiC particles act as nucleation centres, hindering the growth of crystal cells, promoting the formation of the austenite phase, and forming fine equiaxed structures, which increases the strength. However, excessive TiC particles aggravate the spheroidisation during the process of SLM, leading to increased defects, as well as a decrease in density and corrosion resistance.

This research explored a novel chemical reduction of organic aluminum for plating Al on a graphene surface. The thermodynamics of the Al plating reaction process were studied. The Al plating process consisted of two stages: the first was to prepare (C₂H₅)₃Al. In this reaction, the ΔH(enthalpy) was 10.64 kcal/mol, the ΔG(Gibbs free energy) was 19.87 kcal/mol and the ΔS(entropy) was 30.9 cal/(mol·K); this was an endothermic reaction. In the second stage, the (C₂H₅)₃Al decomposed into Al atoms, which were gradually deposited on the surface of the graphene and the Al plating formed. At 298.15 K, the ΔH was −20.21 kcal/mol, the ΔG was −54.822 kcal/mol, the ΔS was 116.08 cal/(mol·K) and the enthalpy change was negative, thus indicating an endothermic reaction.

Samples of 17-4PH high-strength steel were processed by selective laser melting (SLM) and solution-processed. The effects of the solution temperature on the microstructure and mechanical properties of the samples were studied. The 17-4PH high-strength steel is primarily composed of martensite, with a small number of austenite phases, and contains many dislocations. After the solution treatment, the grain size gradually increased, yielding typical martensite. The samples were subjected to an aging treatment after the solution treatment. Precipitates formed in the samples, conducive to improving their strength and hardness. The Vickers hardening and wear properties of the 17-4PH high-strength steel samples first increased and then decreased with increasing solution temperature. After the solution treatment at 1040 °C for 2 h and aging at 480 °C for 4 h, the Vickers hardening of the 17-4PH high-strength steel increased to 392 HV0.5, and the friction coefficient was approximately 0.6. These values were, respectively, 7% and 5% higher than those for the untreated samples.

In order to improve the abrasion performance of 316Lss, make full use of its advantages and broaden its application fields, the tribological behavior of the TiC particles reinforced 316Lss composites—which were manufactured by selective laser melting (SLM)—were investigated. In this study, GCr15 bearing steel was selected as the friction material and experiments on the sliding friction and wear under different loads of 15 N, 25 N and 35 N at the sliding speeds of 60, 80 and 100 mm/min were carried out, respectively. The results show that the wear performance of the TiC/316Lss composite is higher than that of the matrix during the friction and wear experiments under all conditions and the wear rate of the TiC/316Lss composite decreases with increasing the friction rate. Similar to the wear mechanism under different loads, it changes from abrasive wear to delamination wear and severe oxidative wear. At the same time, the mechanical mixed layer formed at a high speed has a protective effect on the matrix. The reason for this phenomenon is that the mechanical properties of the TiC/316Lss composites are significantly improved due to the addition of TiC particles, the refinement of cells near the TiC particles and the formation of a large number of dislocations. In addition, due to the presence of the TiC particles, the hardness and strength of the TiC/316Lss composites are greatly improved, thus the processing hardening ability of sub-surface has been improved.