A nanocomposite CrAlSiN–AlSiN coating with periodically modulated composition was developed and investigated regarding the effect of the composition and structure on the mechanical properties. The modulation was performed by variation of the pressure, cathode current and bias voltage during deposition. The structure and composition of the coating were investigated by X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS) analyses. The coating had a nanocomposite structure consisting of (CrAl)N and (AlSi)N nanograins embedded in a Si₃N₄ matrix. The EDS analysis of the cross-section revealed that the period composition had changed from Cr₀₅₁Al_0.41Si_0.08N to Al_0.82Cr_0.04Si_0.14N. It was shown that the elastic modulus could be adjusted by composition modulation. The coating hardness of 54 GPa was obtained by nanoindentation. The modulated CrAlSiN–AlSiN coating exhibited improved elastic strain to failure (H/E* = 0.11, H—nanohardness, E*—the effective elastic modulus), excellent resistance to plastic deformation (H³/E*² = 0.72), and elastic recovery of 70%, which suggested improved toughness.

This paper presents the results of the investigation of a multilayer TiAlSiN/AlSiN coating. A novel coating architecture with a period consisting of nanocomposite sublayers of TiAlSiN and AlSiN was developed. We discovered that the combination of a harder sublayer with a more elastic one allows for obtaining a suitable combination of superhardness and enhanced toughness. The coating was deposited by cathodic arc technology. The EDS, XRD, and XRS analyses revealed that the nanocomposite structure is composed of TiAlSiN and AlSiN nanocrystallites, with sizes of 12–13 nm and 4–5 nm, respectively. The nanograin phase is incorporated in an amorphous Si₃N₄ matrix. The achieved structure causes the presence of four factors contributing to the hardness increase: nanocomposition, solid solution, refinement hardening, and the formation of many interfaces. An instrumented indentation test was used to investigate the mechanical properties. The developed coating possesses a superhardness of 49.5 GPa and a low elastic modulus of 430 GPa, resulting in an improved elastic strain resistance of 0.11, a plastic deformation resistance of 0.58 GPa, and an elastic recovery of 68%. These results imply that the developed coating combines high stability with mechanical degradation under external influence and provides an improved ability to absorb energy at deformation before fracture, and high elastic recovery. The investigation of the effect of the period modulation on the structure, composition, and mechanical properties of the nanocomposite multilayer TiAlSiN/AlSiN coating showed that the superhardness was due to the nanocomposite and solid solution hardening rather than the increased number of interfaces. The demonstrated combination of superhardness with high elasticity and improved toughness determines the developed nanocomposite TiAlSiN/AlSiN coating as very suitable for industrial applications such as high speed and dry machining.

Titanium-aluminium base nanomultilayer (NML) coatings are deposited by cathodic arc evaporation using pure titanium and aluminium with eighteen percent silicon cathodes. Each multilayer Ti-Al-Si-N structure consists of 49 bi-layers with differ...

This article presents results from a study on the properties of nanostructured multilayered TiN/ZrN coatings with different modulation periods deposited by cathodic-arc evaporation from Ti and Zr targets in nitrogen atmosphere on high-speed steel substrates. The thickness of the TiN-ZrN bilayers varied from 12 nm to 52 nm depending on the rotation speed of the holder. In order to investigate the effect of heat treatment on the mechanical and structural properties, the multilayer ZrN/TiN coatings were annealed in Ar atmosphere at different temperatures for two hours. The surface morphology, elemental composition, nano-hardness and adhesion strength of the as-deposited and annealed coatings were analyzed by scanning electron microscopy complemented with energy dispersive X-ray spectroscopy analysis, and nanoindentation and micro-scratch tests. The results obtained show that the mechanical properties of multilayer TiN/ZrN coatings are considerably improved in comparison to those of the monolayer ZrN and TiN coatings.

A CrAlSiN-AlSiN coating with periodically modulated composition was investigated regarding dependence of the mechanical properties and toughness, morphology, composition, and structure on thermal treatment in the interval of 600–900 °C in argon ambience. The coating exhibited superhardness and high toughness up to 800 °C. A very slight decrease in the nanohardness, resistance to elastic strain to failure, and plastic deformation were observed. The coating had enhanced elastic recovery stable up to 700 °C. It was found that the coating morphology was not substantially influenced by the thermal treatment. X-ray diffraction (XRD) analysis revealed that the modulated coating had a nanocomposite structure, which did not change after annealing, even at 900 °C. The grains were composed mainly of fcc-CrN and h-AlN phases embedded into an amorphous Si₃N₄ matrix. A small amount of an h-Cr₂N phase appeared after heating at temperatures above 700 °C. The coating composition was examined by energy-dispersive X-ray spectroscopy (EDS). The coating was stoichiometric up to 800 °C. It became sub-stoichiometric with respect to nitrogen after annealing at 800 °C and 900 °C. It is thus concluded that the CrAlSiN-AlSiN coating with a periodically modulated structure keeps the combination of superhardness (45.3 GPa) and improved toughness (H³/E*² = 0.362 GPa, elastic recovery 57%) at temperatures up to 800 °C, and is suitable for high thermal applications.

A preliminary investigation of the optical properties of complex Cr-based hard coatings and their connection with the compound structure of the coatings is presented. Cr/CrN, Cr/CrN/CrAlN, Cr/CrN/CrTiAlN, and Cr/CrN/CrAlTiN coating structures were deposited through unbalanced magnetron sputtering. Their mechanical properties, especially nanohardness, coefficient of friction, and adhesion, were measured. The structure and composition of the coatings were characterised through SEM, FIB, XPS, and TEM. Their optical properties were investigated by UV-VIS ellipsometry. The optical parameters’ phase difference Δ, the amplitude ratio Ψ, the frequency-dependent real (ε₁(ω)) and imaginary (ε₂(ω)) part of the dielectric function, and the corresponding refractive and extinction indexes n(ω) and k(ω) were measured and modelled via regression analysis implemented using the WVASE© software version 3.686. Satisfactory coincidence was achieved between the measured optical data and the corresponding fitting models. The physical polycrystalline optical constants of the industrial samples were extracted from modelling data with roughness. The analysis of the data showed that ellipsometric characterisation can be used in order to determine the physical properties of Cr-based hard coatings with complex structure and composition, as well as for repeatability control of the deposition process. However, more detailed research is needed to predict the composition based on measured optical properties.