Micael Borges

Mr. Micael Borges

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2020 in Theoretical and Applied Fracture Mechanics
Verified
Journal Article
Closed access
MBMicael Borges
Micael Borges
DND.M. Neto
D.M. Neto
FAF.V. Antunes
F.V. Antunes

1 March 2020 in International Journal of Fatigue
Verified
Journal Article
Closed access
MBMicael Borges
Micael Borges
F.V. AntunesF.V. Antunes
F.V. Antunes
Pedro PratesPedro Prates
Pedro Prates
Ricardo BrancoRicardo Branco
Ricardo Branco
TVT. Vojtek
T. Vojtek

4 December 2020 in Materials
Verified
Journal Article
Open access
PDF file
MBMicael Borges
Micael Borges
Diogo NetoDiogo Neto
Diogo Neto
F.V. AntunesF.V. Antunes
F.V. Antunes
Fatigue crack growth (FCG) has been studied for decades; however, several aspects are still objects of controversy. The objective here is to discuss different issues, using a numerical approach based on crack tip plastic strain, assuming that FCG is driven by crack tip deformation. ΔK was found to control cyclic plastic deformation at the crack tip, while Kmax has no effect. Therefore, alternative mechanisms are required to justify models based on ΔK and Kmax. The analysis of crack tip plastic deformation also showed that there is crack tip damage below crack closure. Therefore, the definition of an effective load range ΔKeff = Kmax − Kopen is not correct, because the portion of load range below opening also contributes to FCG. Below crack closure, damage occurs during unloading while during loading the crack tip deformation is elastic. However, if the maximum load is decreased below the elastic limit, which corresponds to the transition between elastic and elasto–plastic regimes, there is no crack tip damage. Additionally, a significant effect of the crack ligament on crack closure was found in tests with different crack lengths and the same ΔK. Finally, the analysis of FCG after an overload with and without contact of crack flanks showed that the typical variation of da/dN observed is linked to crack closure variations, while the residual stresses ahead of crack tip are not affected by the contact of crack flanks.

1 April 2020 in Theoretical and Applied Fracture Mechanics
Verified
Journal Article
Closed access
MBMicael Borges
Micael Borges
FAF.V. Antunes
F.V. Antunes
Pedro PratesPedro Prates
Pedro Prates
Ricardo BrancoRicardo Branco
Ricardo Branco
ACA.S. Cruces
A.S. Cruces
PLP. Lopez-Crespo
P. Lopez-Crespo

25 January 2020 in Metals
Verified
Journal Article
Open access
PDF file
MBMicael Borges
Micael Borges
F.V. AntunesF.V. Antunes
F.V. Antunes
Pedro PratesPedro Prates
Pedro Prates
Ricardo BrancoRicardo Branco
Ricardo Branco
The consideration of plastic crack tip opening displacement (CTOD, δp), as a crack driving force has given us the opportunity to predict fatigue crack growth (FCG) rate numerically, and, therefore, to develop parametric studies focused on the effect of loading, geometrical, and material parameters. The objective here is to study the effect of the isotropic hardening parameters of the Voce law on FCG, which are the isotropic saturation stress, YSat, and the isotropic saturation rate, CY. The increase of these hardening parameters causes δp to decrease. However, this effect is much more pronounced for YSat than CY. The variation is non-linear, and the rate of variation decreases with the increase of isotropic parameters. The increase of YSat increases the crack closure phenomenon. Finally, the influence of the isotropic parameters is more relevant for pure isotropic hardening than for mixed hardening.

17 June 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
MBMicael Borges
Micael Borges
MCManuel Caldas
Manuel Caldas
F.V. AntunesF.V. Antunes
F.V. Antunes
Ricardo BrancoRicardo Branco
Ricardo Branco
Pedro PratesPedro Prates
Pedro Prates
A numerical approach based on plastic crack tip opening displacement (CTOD) was followed to study fatigue crack growth (FCG) from notches. The identification of fundamental mechanisms was made considering notched and unnotched models, with and without contact of crack flanks. Different parameters were studied, namely, notch radius, crack length, stress state, and material. The notch increases the plastic CTOD, and therefore fatigue crack growth rate, da/dN, as expected. The reduction of notch radius increases da/dN but reduces the notch affected zone. Ahead of the notch affected zone, da/dN increases linearly with crack growth, with a rate that increases linearly with the plastic CTOD. The crack closure phenomenon has a dramatic effect under plane stress conditions but a limited effect on plane strain conditions. In the former case, the contact of crack flanks reduces substantially the effect of notch radius and the size of the notch affected zone. These trends are associated with the increase of crack closure level with notch radius. The material does not affect the global trends, but the reduction of yield stress increases the level of plastic deformation and therefore da/dN. The effect of material, and also of stress state, is mainly associated with crack closure.