To facilitate applications such as environment detection or disaster monitoring, the development of rapid low cost systems for collecting near real time spatial information is very critical. Rapid spatial information collection has become an emerging trend for remote sensing and mapping applications. In this study, a fixed-wing Unmanned Aerial Vehicle (UAV)-based spatial information acquisition platform that can operate in Ground Control Point (GCP) free environments is developed and evaluated. The proposed UAV based photogrammetric platform has a Direct Georeferencing (DG) module that includes a low cost Micro Electro Mechanical Systems (MEMS) Inertial Navigation System (INS)/ Global Positioning System (GPS) integrated system. The DG module is able to provide GPS single frequency carrier phase measurements for differential processing to obtain sufficient positioning accuracy. All necessary calibration procedures are implemented. Ultimately, a flight test is performed to verify the positioning accuracy in DG mode without using GCPs. The preliminary results of positioning accuracy in DG mode illustrate that horizontal positioning accuracies in the x and y axes are around 5 m at 300 m flight height above the ground. The positioning accuracy of the z axis is below 10 m. Therefore, the proposed platform is relatively safe and inexpensive for collecting critical spatial information for urgent response such as disaster relief and assessment applications where GCPs are not available.
Spatial information plays a critical role in remote sensing and mapping applications such as environment surveying and disaster monitoring. An Unmanned Aerial Vehicle (UAV)-borne mobile mapping system (MMS) can accomplish rapid spatial information acquisition under limited sky conditions with better mobility and flexibility than other means. This study proposes a long endurance Direct Geo-referencing (DG)-based fixed-wing UAV photogrammetric platform and two DG modules that each use different commercial Micro-Electro Mechanical Systems’ (MEMS) tactical grade Inertial Measurement Units (IMUs). Furthermore, this study develops a novel kinematic calibration method which includes lever arms, boresight angles and camera shutter delay to improve positioning accuracy. The new calibration method is then compared with the traditional calibration approach. The results show that the accuracy of the DG can be significantly improved by flying at a lower altitude using the new higher specification hardware. The new proposed method improves the accuracy of DG by about 20%. The preliminary results show that two-dimensional (2D) horizontal DG positioning accuracy is around 5.8 m at a flight height of 300 m using the newly designed tactical grade integrated Positioning and Orientation System (POS). The positioning accuracy in three-dimensions (3D) is less than 8 m.
Smartphones have become indispensable in our daily lives. Their various embedded sensors have inspired innovations in mobile applications—especially for indoor navigation. However, the accuracy, reliability and generalizability of navigation all continue to struggle in environments lacking a Global Navigation Satellite System (GNSS). Pedestrian Dead Reckoning (PDR) is a popular method for indoor pedestrian navigation. Unfortunately, due to its fundamental principles, even a small navigation error will amplify itself, step by step, generally leading to the need for supplementary resources to maintain navigation accuracy. Virtually all mobile devices and most robots contain a basic camera sensor, which has led to the popularity of image-based localization, and vice versa. However, all of the image-based localization requires continuous images for uninterrupted positioning. Furthermore, the solutions provided by either image-based localization or a PDR are usually in a relative coordinate system. Therefore, this research proposes a system, which uses space resection-aided PDR with geo-referenced images of a previously mapped environment to enable seamless navigation and solve the shortcomings of PDR and image-based localization, and evaluates the performance of space resection with different assumptions using a smartphone. The indoor mobile mapping system (IMMS) is used for the effective production of geo-referenced images. The preliminary results indicate that the proposed algorithm is suitable for universal pedestrian indoor navigation, achieving the accuracy required for commercial applications.
27 July 2012 in The International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences
Nowadays the most common technologies used for positioning and orientation of a mobile mapping system include using Global Navigation Satellite System (GNSS) as a major positioning sensor and Inertial Navigation System (INS) as the major orientation sensor. The integration strategy of the most commercially system is the loosely coupled (LC) architecture, that has the simplest architecture using the GNSS solutions to aid the INS navigation information with proper optimization estimator. The LC does combine the two sensors’ solutions when the number of tracked satellite is more than four. In recent year, another commonly integration strategy is known as tightly coupled (TC) architecture. Because the TC uses the GNSS measurements to aid INS, it can integrate measurements provided by GNSS receiver and INS unless no GNSS satellite is tracked. Obviously, the TC architecture is a better candidate for land based mobile mapping applications than LC in Taiwan. Unfortunately, there are still many GNSS denied environment in the urban area, therefore the TC architecture is still not robust and stable enough for MMS application. The overall objective of this paper is to provide a scheme that tightly integrates INS/GNSS and Photogrammetric for land based MMS applications with sufficient and stable POS solutions during GNSS outages. In the traditional photogrammetry operation, numerous ground control points are applied to compute those Exterior Orientation Parameters (EOPs) of cameras by bundle adjustment. The key opinion is to derive the INS centre position and attitude and reconstruct 3-D tracking and 3-D object space by cameras EOPs. The proposed algorithm is verified using field test data collected in GNSS denied environments and the preliminary results presented in this study illustrated that the proposed algorithm is able to provide 60% improvement in terms of positioning and orientation accuracy in Taipei and Tainan cities.
3 June 2016 in The International Archives of the Photogrammetry, Remote Sensing and Spatial Information Sciences
The early development of mobile mapping system (MMS) was restricted to applications that permitted the determination of the elements of exterior orientation from existing ground control. Mobile mapping refers to a means of collecting geospatial data using mapping sensors that are mounted on a mobile platform. Research works concerning mobile mapping dates back to the late 1980s. This process is mainly driven by the need for highway infrastructure mapping and transportation corridor inventories. In the early nineties, advances in satellite and inertial technology made it possible to think about mobile mapping in a different way. Instead of using ground control points as references for orienting the images in space, the trajectory and attitude of the imager platform could now be determined directly. Cameras, along with navigation and positioning sensors are integrated and mounted on a land vehicle for mapping purposes. Objects of interest can be directly measured and mapped from images that have been georeferenced using navigation and positioning sensors. Direct georeferencing (DG) is the determination of time-variable position and orientation parameters for a mobile digital imager. The most common technologies used for this purpose today are satellite positioning using the Global Navigation Satellite System (GNSS) and inertial navigation using an Inertial Measuring Unit (IMU). Although either technology used along could in principle determine both position and orientation, they are usually integrated in such a way that the IMU is the main orientation sensor, while the GNSS receiver is the main position sensor. However, GNSS signals are obstructed due to limited number of visible satellites in GNSS denied environments such as urban canyon, foliage, tunnel and indoor that cause the GNSS gap or interfered by reflected signals that cause abnormal measurement residuals thus deteriorates the positioning accuracy in GNSS denied environments. This study aims at developing a novel method that uses ground control points to maintain the positioning accuracy of the MMS in GNSS denied environments. At last, this study analyses the performance of proposed method using about 20 check-points through DG process.