Ferrite isolators are attractive due to their excellent isolation, low loss, good linearity, and high-power performance. However, these devices usually operate over a single-frequency band. Multiband applications are possible if the isolation bandwidth of an isolator can be tuned. This paper presents a tunable waveguide-based full-mode ferrite isolator as well as a more compact half-mode tunable isolator, both fabricated on yttrium-iron-garnet substrates. For the first time, theory and design guidelines for the center frequency, bandwidth, and tuning of the ferrite isolators' unidirectional magnetostatic surface wave (MSW) mode are presented. The proposed theoretical model reveals that the isolation bandwidth can exceed 100% if the magnetization-to-bias field ratio is higher than 8. Although the full-mode design is fabricated using a conventional subtractive technique, the half-mode design is implemented using inkjet printing technology. The full-mode isolator provides a maximum bandwidth of 45% and a peak isolator figure of merit (IFM) of over 65 dB at 7 GHz, whereas the half-mode design has a maximum bandwidth of 59% and a peak IFM of 76.7 dB at 7.5 GHz. The tuning of the center frequency is from 7 to 10.7 GHz for the full-mode and from 4.4 to 9.9 GHz for the half-mode design using magnetic field strengths up to 2500 and 2400 Oe, respectively. This paper demonstrates the versatility of ferrite isolators as tunable microwave devices for reconfigurable RF applications.
This paper describes the design, implementation, and testing of a novel multi-function software defined Radio Frequency (RF) system designed for small airborne drone applications. The system was created using an inexpensive Field Programmable Gate Array (FPGA) to combine a coherent linear frequency modulated radar transmitter and receiver, with a Digital Radio Frequency Memory (DRFM) jammer for use with a common RF aperture in simultaneous operation. The system was implemented on a Xilinx Kintex-7 FPGA with a wideband analogue-to-digital/ digital-to-analogue (ADC/DAC) converter mezzanine board and tested using hardware-in-the-loop mode to validate its performance. This is the first known account of an integrated multifunction electronic attack and radar system on a single chip, capable of performing a simultaneous, not time shared, operation.
24 June 2015 in IEEE Transactions on Components, Packaging and Manufacturing Technology
This paper shows a study of a new ferrite low-temperature cofired ceramic (LTCC) circulator with integrated winding. The external magnets used in traditional circulators must be strong to overcome the ferrite's demagnetization factor. The novel circulator presented herein uses an embedded winding within the ferrite to magnetize the material from the inside, thereby significantly reducing the demagnetization effects. Because of the controllability of the bias field, the resulting device is also multifunctional: when the windings are energized by a current, the device operates as a dynamic circulator in which the circulation direction can be changed by switching the direction of the current. If an external magnet is placed on the circulator, its operating frequency can be changed by adjusting the bias current. Unlike other LTCC circulators with external magnets, the proposed device can even operate as a power splitter by removing the bias current. A circulator prototype has been characterized in three states: unbiased, biased by windings, and biased by windings and external magnets. When no current is applied, the transmission of each port is about -5 dB with a return loss better than 20 dB at 14.8 GHz. When a current of 300 mA is injected into the windings, the measured insertion loss and isolation of the circulator are approximately 3 and 8 dB, respectively, whereas the return loss is better than 20 dB at 14.2 GHz. When external magnets are added in addition to a current of 200 mA, the insertion loss and isolation improve to 1.6 and 23 dB, respectively, at 14.2 GHz. The variation of the circulator's working frequency is 0.6 GHz. This is achieved first by the change of internal magnetization M when current is less than 120 mA, then the heat due to the winding increases the ferrite's μeff, leading to more frequency shifting. The total size(L×W×H)is8mm×8mm×1.1mm.
25 January 2018 in IEEE Transactions on Electromagnetic Compatibility
Alien crosstalk (AXT) between Ethernet cables produces interference and poses a potential threat to system security. AXT is challenging to measure in pre-existing installations because of the need for instrumentation at both the near- and far ends. Although commercially available portable equipment for this purpose exists, baluns must be used to excite the balanced modes on Ethernet cables, which restricts the bandwidth and includes the unwanted response of the baluns. Here, a novel measurement system is proposed that does not use baluns. The proposed system uses unbalanced network analyzers that are placed at both ends of the cable run. The analyzers are synchronized and phase locked, and the resulting unbalanced crosstalk measurements are then mathematically converted to balanced and common modes. A new calibration method for multiple network analyzers is presented and validated. Worst-case alien crosstalk measurements of Category 6 unshielded twisted pairs using the proposed system are then presented.
Establishing an error in the angle estimates of a monopulse radar is critical to creating miss distance during the terminal stage of missile engagements. However, the tools for creating angle deception are limited, with blink jamming offering significant potential. This paper fills in the conceptual gaps in understanding of blink jamming, through a theoretical analysis, which is validated using modelling and simulation, including hardware-in-the-loop with a Field Programmable Gate Array (FPGA). Additionally, a novel version of blink jamming is proposed, using a synchronized amplitude modulation, and its performance compared to traditional, unmodulated blink jamming. The complete results are discussed, with design guidance provided for implementing blink jamming in operational scenarios.
1 July 2019 in IEEE Antennas and Propagation Magazine
The Thévenin and Norton equivalent models of a receiving antenna cannot be used to calculate the antenna's scattered power because they are too simplistic. Based on the reciprocity theorem, a more elaborate equivalent model, consisting of a passive distributed transformer, is proposed for wire antennas in both the transmit and receive modes. The model parameters are derived from the antenna's transfer admittance parameters, the latter obtained under short circuit loading conditions in transmit mode only. A method is then applied to determine the new admittance parameters when the antenna is perturbed by an arbitrary load, which allows the receive-mode current distribution on the antenna to be calculated. Once the receive-mode current is known,scattered power can be calculated with a formula that avoids integration over the far-field sphere. The method has been applied to a λ/2dipole, λ-dipole, and three-element Yagi antenna for resistive loads spanning up to nine decades. Calculated scattered-power values are shown to agree almost perfectly with values obtained using a commercial simulator, thus demonstrating that it is possible to calculate scattered power based on the characterization of the antenna in transmit mode only. Results indicate that the aperture efficiency of a dipole antenna can exceed 50% when it is connected to a mismatched load. Finally, a newly defined transducer efficiency is presented, which can be used to choose an optimum load to obtain the best compromise between the aperture and scattering areas.