A hydraulic cylinder is a mechanical actuator that is widely used in different industries such as construction, manufacturing, aerospace, and offshore oil and gas. Seal wear in hydraulic cylinders results in hydraulic fluid leakage or contamination of the hydraulic fluid. Untimely, failure of a hydraulic cylinder increases the maintenance cost and reduces productivity. Therefore, condition monitoring of the hydraulic cylinder is necessary to understand the current state of equipment. In the literature, there have been numerous documented attempts to perform condition monitoring of hydraulic cylinders using different methods, based on fluid properties, pressure, vibration, and acoustic emission. However, there have been limited attempts to present a state-of-the-art review of condition monitoring of hydraulic cylinders. This article presents an overview of the methods used for the condition monitoring of hydraulic cylinders, including the detection of different failure modes using different sensors, the separability of fault conditions using sensor-based features, and the ability to pick up incipient faults by sensor-based features. This information is required for new readers in this area of expertise. This article summarizes different condition monitoring methods that have been used from its early implementation to very recent dates, aiming at clarifying recent advances and identifying challenges in the research of the condition monitoring of hydraulic cylinders. It is anticipated that the information presented in this article will be beneficial for new researchers and provide directions for future research in the area of condition monitoring of hydraulic cylinders.
21 July 2020 in The International Journal of Advanced Manufacturing Technology
In recent years, there has been a growing concern for fluid spill from hydraulic cylinders in the offshore oil and gas industry. To diagnose the leakage from hydraulic cylinders, there have been attempts made in literature using fluid and pressure-based condition monitoring techniques. However, there have been limited attempts to monitor leakage from hydraulic cylinders using acoustic emissions. Therefore, in this paper, an attempt has been made to understand the fluid leakage in the hydraulic cylinder based on acoustic emissions. An experimental study was performed using a test rig (with a water-glycol as hydraulic fluid) which closely replicates the operation of a hydraulic cylinder. As piston rod seal failure is the foremost cause for leakage, experiments were performed using unworn, semi-worn, and worn piston rod seals. For each seal condition, experiments were performed for five strokes at pressure conditions of 10, 20, 30, and 40 bar. In this study, the continuous acoustic emission signal was observed for each hydraulic cylinder stroke. Acoustic emission data was analysed using different techniques such as time domain, frequency domain, and time-frequency technique. By using acoustic emission features such as root mean square (RMS), peak, skewness, median frequency, and mean frequency, it was possible to identify and separate non-leakage and leakage conditions in the test rig. By using AE bandpower and power spectral density features, it is also possible to identify the leakage due to semi-worn seal and worn seal in the test rig. This study lays a strong basis to develop a real-time monitoring technique based on acoustic emissions to monitor the health of piston rod seals used in the hydraulic cylinder in the offshore industry.
The foremost reason for unscheduled maintenance of hydraulic cylinders in industry is caused by wear of the hydraulic seals. Therefore, condition monitoring and subsequent estimation of remaining useful life (RUL) methods are highly sought after by the maintenance professionals. This study aimed at investigating the use of acoustic emission (AE) sensors to identify the early stages of external leakage initiation in hydraulic cylinders through run to failure studies (RTF) in a test rig. In this study, the impact of sensor location and rod speeds on the AE signal were investigated using both time- and frequency-based features. Furthermore, a frequency domain analysis was conducted to investigate the power spectral density (PSD) of the AE signal. An accelerated leakage initiation process was performed by creating longitudinal scratches on the piston rod. In addition, the effect on the AE signal from pausing the test rig for a prolonged duration during the RTF tests was investigated. From the extracted features of the AE signal, the root mean square (RMS) feature was observed to be a potent condition indicator (CI) to understand the leakage initiation. In this study, the AE signal showed a large drop in the RMS value caused by the pause in the RTF test operations. However, the RMS value at leakage initiation is seen to be a promising CI because it appears to be linearly scalable to operational conditions such as pressure and speed, with good accuracy, for predicting the leakage threshold.
28 May 2021 in The International Journal of Advanced Manufacturing Technology
Fluid leakage from hydraulic cylinders is a major concern for the offshore industries as it directly affects hydraulic cylinder energy efficiency and causes environmental contamination. There have been attempts made in literature to develop robust condition monitoring techniques for hydraulic cylinders. However, most of these studies were performed to identify degradation of single components. Therefore, in this study, the aim is to monitor degradation of multiple components simultaneously in hydraulic cylinders using acoustic emissions. Experiments performed consist of three test phases and were performed using a hydraulic test rig. In the first test phase, the study is performed to identify acoustic emission features that can be used to monitor piston rod seal wear. In the second test phase, acoustic emission features are identified that can be used to understand bearing wear when unworn, semi-worn or worn piston rod seals are used in hydraulic test rig. In the third test phase, a run-to-failure test is conducted to identify acoustic emission features that can indicate fluid leakage initiation due to piston rod seal wear. The median frequency feature showed good repeatability in all the three test phases to identify piston rod seal wear, bearing wear and fluid leakage initiation during the initial stages in the hydraulic test rig. The proposed acoustic emission-based condition monitoring technique is robust and can be used for the hydraulic cylinders in the industries, as it identifies acoustic emission features based on particular frequency bands associated to specific components, making it less susceptible to noise from other components.
Hydropower is a cost-effective, reliable, and programmable renewable energy source. Many hydropower plants worldwide have been in operation for decades and now need maintenance and refurbishment. While failures in hydroelectric plants are uncommon, they can be catastrophic and lead to prolonged downtimes. Thus, robust monitoring strategies are essential to track failure modes in critical components, preventing breakdowns and productivity losses. However, very few attempts are made to consolidate the new knowledge developed in this area in a state-of-the-art review paper. Therefore in this paper, we discussed the state-of-the-art sensing technologies that can be used to monitor critical components in hydropower turbines, their common failure causes and effects, identifying intermittent failures using various sensing technologies, and sensor locations to monitor these critical parts. In this state-of-the-art review, we identified that blades, nozzles and needles, bearings, and shafts are some of the critical parts in turbine that require continuous monitoring. For these critical components, vibration-based monitoring can be used to monitor the wear due to erosion, cavitation, wear, misalignment, or looseness. The information presented in this state-of-the-art review will be beneficial to new researchers getting accustomed to hydropower condition monitoring, and will assist the industry in developing new turbine condition monitoring strategies and technologies.
Seal wear in hydraulic cylinders results in fluid leakage, and instability of the piston rod movement. Therefore, regular inspection of seals is required using automated approaches to improve productivity and to reduce unscheduled maintenance. In literature, successful attempts have been made using acoustic emission-based condition monitoring to classify the seal wear. However, limited attempts have been made to implement automated approaches to classify seal wear using acoustic emission features. Therefore, this article presents an automated approach for rapid and computationally economical diagnosis of seal wear using acoustic emission. The experiments were performed at varying pressure conditions on a hydraulic test rig that can simulate fluid leakage conditions similar to that of hydraulic cylinders. From the acoustic emission spectrum, the frequency bands were identified with peak power and by heterodyning the signal. This technique results in 10X downsampling without losing the information of interest. Further, the signal was divided into smaller “snapshots” to facilitate rapid diagnosis. In these tests, the diagnosis was made on short-time windows, as low as 0.3 seconds in length. A set of time and frequency domain features were designed, and the Support Vector Machine (SVM) was trained on 60 % of the test cases generated with seals of three different conditions. The SVM was able to accurately classify the status irrespective of the pressure conditions, with an accuracy of ~99 %. Therefore, the proposed automated seal wear classification technique based on acoustic emission and SVM can be used for real-time monitoring of seal wear in hydraulic cylinders.