This article describes the manufacturing technology of biocompatible flexible strain-sensitive sensor based on Ecoflex silicone and multi-walled carbon nanotubes (MWCNT). The sensor demonstrates resistive behavior. Structural, electrical, and mechanical characteristics are compared. It is shown that laser radiation significantly reduces the resistance of the material. Through laser radiation, electrically conductive networks of MWCNT are formed in a silicone matrix. The developed sensor demonstrates highly sensitive characteristics: gauge factor at 100% elongation −4.9, gauge factor at 90° bending −0.9%/deg, stretchability up to 725%, tensile strength 0.7 MPa, modulus of elasticity at 100% 46 kPa, and the temperature coefficient of resistance in the range of 30–40 °C is −2 × 10⁻³. There is a linear sensor response (with 1 ms response time) with a low hysteresis of ≤3%. An electronic unit for reading and processing sensor signals based on the ATXMEGA8E5-AU microcontroller has been developed. The unit was set to operate the sensor in the range of electrical resistance 5–150 kOhm. The Bluetooth module made it possible to transfer the received data to a personal computer. Currently, in the field of wearable technologies and health monitoring, a vital need is the development of flexible sensors attached to the human body to track various indicators. By integrating the sensor with the joints of the human hand, effective movement sensing has been demonstrated.

The efficiency of devices for biomedical applications, including tissue engineering and neuronal stimulation, heavily depends on their biocompatibility and performance level. Therefore, it is important to find adequate materials that meet the necessary requirements such as (i) being intrinsically compatible with biological systems, (ii) providing a sufficient electronic conductivity that promotes efficient signal transduction, (iii) having “soft” mechanical properties comparable to biological structures, and (iv) being degradable in physiological solution. We have developed organic conducting biocompatible single-walled carbon nanotubes (SWCNT) composites based on bovine serum albumin, carboxymethylcellulose, and acrylic polymer and investigated their properties, which are relevant for biomedical applications. This includes ζ-potential measurements, conductivity analyses, and SEM micrographs, the latter providing a local analysis of SWCNT distribution in the base material. We observed the development of the electrical conductivity of the SWCNT composites exposed to 1 mM KCl electrolyte for 40 days, representing a high stability of the samples. The conductivity of samples reaches 1300 S/m for 0.45 wt.% nanotubes. Moreover, we demonstrated the biocompatibility of the composites via cultivating fibroblast cell culture. Finally, we showed that composite coating results in the longer lifespan of cells on the surface. Overall, the SWCNT-based conductive composites might be a promising material for extended biomedical applications.

The present study aims to use enhanced ionic polymer–metal composites (IPMC) as an artificial muscle (a soft-active actuator) to restore eyelid movement of patients with ptosis. The previous eyelid movement mechanisms contained drawbacks, specifically in the lower eyelid. We used finite element analysis (FEA) to find the optimal mechanism among two different models (A and B). In addition to common electrodes of IPMC (gold and platinum), the bovine serum albumin (BSA) and microcrystalline cellulose (MCC) polymers, with optimal weight percentages of carbon nanotube (CNT) nanofiller, were also utilized as non-metallic electrodes to improve the efficiency of the IPMC actuator. In both models, IPMC with nanocomposite electrodes had higher efficiency as compared to the metallic electrodes. In model A, which moved eyelids indirectly, IPMC with MCC-CNT electrode generated a higher force (25.4%) and less stress (5.9 times) as compared to IPMC with BSA-CNT electrode. However, the use of model A (even with IPMCs) with nanocomposite electrodes can have limitations such as possible malposition issues in the eyelids (especially lower). IPMC with MCC-CNT nanocomposite electrode under model B, which moved eyelids directly, was the most efficient option to restore eyelid movement. It led to higher displacements and lower mechanical stress damage as compared to the BSA-CNT. This finding may provide surgeons with valuable data to open a window in the treatment of patients with ptosis.

Currently, an urgent need in the field of wearable electronics is the development of flexible sensors that can be attached to the human body to monitor various physiological indicators and movements. In this work, we propose a method for forming an electrically conductive network of multi-walled carbon nanotubes (MWCNT) in a matrix of silicone elastomer to make stretchable sensors sensitive to mechanical strain. The electrical conductivity and sensitivity characteristics of the sensor were improved by using laser exposure, through the effect of forming strong carbon nanotube (CNT) networks. The initial electrical resistance of the sensors obtained using laser technology was ~3 kOhm (in the absence of deformation) at a low concentration of nanotubes of 3 wt% in composition. For comparison, in a similar manufacturing process, but without laser exposure, the active material had significantly higher values of electrical resistance, which was ~19 kOhm in this case. The laser-fabricated sensors have a high tensile sensitivity (gauge factor ~10), linearity of >0.97, a low hysteresis of 2.4%, tensile strength of 963 kPa, and a fast strain response of 1 ms. The low Young’s modulus values of ~47 kPa and the high electrical and sensitivity characteristics of the sensors made it possible to fabricate a smart gesture recognition sensor system based on them, with a recognition accuracy of ~94%. Data reading and visualization were performed using the developed electronic unit based on the ATXMEGA8E5-AU microcontroller and software. The obtained results open great prospects for the application of flexible CNT sensors in intelligent wearable devices (IWDs) for medical and industrial applications.

A combined magnetic field sensor consisting of a magnetic field concentrator based on a superconducting ring film and a magnetically sensitive element with a spintronics structure is investigated. The active strip (narrowed part) of the concentrator is separated by an insulating film from the magnetically sensitive element, i.e. the combined magnetic field sensor is a sandwich. It has been established that the concentration coefficient of a sandwich-type magnetic field can be increased by fragmentation (nanostructuring) of the active band, in the form of several superconducting branches and cuts 20 nm wide. Increasing the number of incisions also reduces the threshold sensitivity of the sensor by several times. Nanostructured elements in the form of nanoscale sections in the active strip allow you to reduce the diameter of the concentrator ring, which allows the sensor to make the maximum linear size less than 1mm. It is noted that the considered combined magnetic field sensor with nanostructured elements has a high potential for detecting ultraweak magnetic fields (∼ 10 pT), and apparently, can be an alternative to SQUID.

On the basis of the previously proposed phenomenological material equation of a superconducting granular medium, numerical simulation of some products from granular superconductors which include, in particular, products from high-temperature superconducting ceramics (and electrodynamic processes in them) is carried out. An expression is obtained for the first critical field of the medium in question and its relation to the phenomenological parameters of the medium. A strip wire model from a granular superconducting medium is constructed, the maximum current of these wires and its dependence on the external magnetic field were obtained. An analogue of the SQUID based on the strip from a granular superconductor is proposed, it is shown that its field characteristic has similarities with the field characteristics of the classical single-contact SQUID.