Wayan Mustika

Mr. Wayan Mustika

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 April 2020 in Geosciences
Verified
Journal Article
Open access
PDF file
MSMinson Simatupang
Minson Simatupang
LMLukas Kano Mangalla
Lukas Kano Mangalla
RERomy Suryaningrat Edwin
Romy Suryaningrat Edwin
APAdris Ade Putra
Adris Ade Putra
MAMuhammad Thahir Azikin
Muhammad Thahir Azikin
WMWayan Mustika
Wayan Mustika
The stabilization of soil through the addition of fly ash has been shown to be an effective alternative for improving the strength and stiffness of soil through the resulting chemical reactions. The chemical reaction that occurs dissociates the lime (CaO) in the fly ash, and the establishment of cementitious and pozzolanic gels (consisting of calcium silicate hydrate (CSH) gel and calcium aluminate hydrate (CAH) gel) binds the soil particles and increases the strength and stiffness of the soil. Investigations into the mechanical properties of sands stabilized with fly ash (fly-ash-stabilized sands) were conducted through a series of unconfined compressive strength (UCS) and direct shear strength tests for various fly ash percentages, curing times, grain sizes, degrees of saturation during sample preparation, and content of fines. It was found that the mechanical properties—UCS and direct shear strength (DSS)—of fly-ash-stabilized sands increased with both increasing fly ash content in the specimen and curing time, but decreased with increasing grain size, degree of saturation during sample preparation, and content of fines. The results indicated that fly-ash-stabilized sands required more than a month to attain their optimum performance with regard to binding sand particles.

1 January 2021 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
PDF file
WMWayan Mustika
Wayan Mustika
AKA Kadir
A Kadir
ENE Ngii
E Ngii
MNM Nurdin
M Nurdin
This study is a follow-up of nickel slag waste used for building construction materials. Paving blocks were made using a mixture of cement and aggregates in a ratio of 1: 3 and 1: 5 which used a mixture of nickel slag waste and natural sand with aggregate gradation in zone III of the rather fine sand category based on SNI 03-2834-2000. Sand substitution with nickel slag waste has used a variation of the composition of the mixture of 0% (without slag), 25%, 75%, and 100% (without sand). The behaviour would be obtained the compressive strength value of paving blocks and average water absorption. Paving blocks compressive strength were tested at the age of 28 days, while the average value of water absorption was performed by immersing the paving block specimens for 24 hours. The physical strength and absorption value of paving block water refer to SNI 03-0691-1996. The results showed that the use of nickel slag waste in making paving blocks could increase the compressive strength of paving blocks, while water absorption in all compositions and variations of the paving blocks mixture was decreased in line with the increase of nickel slag composition.

22 September 2022 in Infrastructures
Verified
Journal Article
Open access
PDF file
MSMinson Simatupang
Minson Simatupang
RERomy Suryaningrat Edwin
Romy Suryaningrat Edwin
SSSulha Sulha
Sulha Sulha
WMWayan Mustika
Wayan Mustika
Heriansyah PutraHeriansyah Putra
Heriansyah Putra
Dede Heri Yuli YantoDede Heri Yuli Yanto
Dede Heri Yuli Yanto
Currently, a soil stabilization approach using fly ash as an effective choice for increasing soil stiffness and strength has emerged. With the presence of water, the lime in the fly ash would be separated, generating cementitious materials binding the grains of sand. In the present study, the influence of curing time and saturation during specimen preparation on the behavior of fly ash-modified sand was observed by performing a series of splitting tensile strength tests. It was found that the splitting tensile strength increases with fly ash content and curing time and decreases with saturation. The splitting tensile strength produced at 30% saturation was approximately two-fold higher than 100%, particularly at one month of curing time. However, the splitting tensile strength at higher saturations approaches lower, especially at longer curing times. Porewater evaporation accelerates the self-hardening occurring over time during curing. By increasing the fly ash percentage from 5% to 20% in the mixture, the splitting tensile strength increased by up to twenty-fold in the present study. An equation has been proposed as a function of porosity/volumetric fly ash content, curing time, and saturation during the preparation of the specimen.

1 January 2020 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
PDF file
ENE Ngii
E Ngii
WMWayan Mustika
Wayan Mustika
ASA S Sukri
A S Sukri
RBR Balaka
R Balaka
RSR Sriyani
R Sriyani
LWL Welendo
L Welendo
This study analyzed the effect of blood clamshell substitution (Anadara granosa) on the mechanical properties of concrete, namely compressive strength and flexural strength, using clamshell material originating from the Bungkutoko island region, Abeli District and Toronipa coastal area Soropia District, Konawe Regency, Southeast Sulawesi Province. In this study, the concrete was made using blood clamshell (Anadara granosa) waste as a substitute for coarse aggregates. As a control, normal concrete was made using natural materials, namely the Moramo split and Pohara sand. The results show that partial substitution of coarse aggregates using blood clamshell concentrations of 15%, 25%, and 50% reduced the compressive strength of concrete by 11.00%, 16.20%, and 30.62% when compared to the control, respectively. Meanwhile, the respective concrete bending strength also decreased by 7.33%, 13.83%, and 32.53%. The compressive strength testing of 28 days-concrete with the shellfish compositions of 15% and 25% showed the values of 25.35 MPa and 23.87 MPa, respectively, which can be categorized as a medium-quality concrete (structural concrete). Meanwhile, the 50% shell composition had a compressive strength of 19.895 MPa, which can be categorized as a low-quality concrete (non-structural concrete).

25 April 2026 in International Journal of Geosynthetics and Ground Engineering
Verified
Journal Article
Closed access
PDF file
SUSulha
Sulha
MSMinson Simatupang
Minson Simatupang
WMWayan Mustika
Wayan Mustika
UMUniadi Mangidi
Uniadi Mangidi
MAMuh. Handy Dwi Adityawan
Muh. Handy Dwi Adityawan

1 January 2024 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
RERomy Suryaningrat Edwin
Romy Suryaningrat Edwin
FMFitriah Masud
Fitriah Masud
SSSulha Sulha
Sulha Sulha
WMWayan Mustika
Wayan Mustika
Concrete and mortar are more straightforward in their production than steel. Besides, the low costs in their production can be obtained by utilizing waste Concrete and mortar are more straightforward in their production than steel. Besides, the low costs in their production can be obtained by utilizing waste