Exhaust gas recirculation has been proposed as a potential strategy for reducing the cost and efficiency penalty associated with postcombustion carbon capture. However, this approach may cause as-yet unresolved effects on the combustion process, including additional potential for the occurrence of thermoacoustic instabilities. Flame dynamics, characterized by the flame transfer function, were measured in traditional swirl stabilized and low-swirl injector combustor configurations, subject to exhaust gas circulation simulated by N2 and CO2 dilution. The flame transfer functions exhibited behavior consistent with a low-pass filter and showed phase dominated by delay. Flame transfer function frequencies were nondimensionalized using Strouhal number to highlight the convective nature of this delay. Dilution was observed to influence the dynamics primarily through its role in changing the size of the flame, indicating that it plays a similar role in determining the dynamics as changes in the equivalence ratio. Notchlike features in the flame transfer function were shown to be related to interference behaviors associated with the convective nature of the flame response. Some similarities between the two stabilization configurations proved limiting and generalization of the physical behaviors will require additional investigation.
6 November 2022 in Journal of Open Source Software
Lookup of thermodynamic properties of substances is a common task in numerous engineering disciplines and is also an important skill taught to students in several common engineering disciplines. While properties were traditionally found using tables of thermodynamic data, availability of modern software has essentially eliminated the need for laborious use of tables, and has created opportunities to support quick iteration and revision of calculations. As thermodynamic data are published in a variety of formats, it is necessary for software to provide a standardized interface to operate on a number of different data source formats. Additionally, thermodynamic software needs to be numerically efficient and robust, to deal with the diverse computational methodologies required to produce property calculations. PYroMat seeks to create a tool that meets these needs and can grow with users at different levels of expertise. It offers a low barrier to entry and is easy enough for students to use, but also powerful and flexible enough to serve the needs of engineering professionals and scientific researchers.
1 May 2021 in Journal of Renewable and Sustainable Energy
Solar generation facilities are inherently spatially distributed and therefore aggregate solar irradiance in both space and time, smoothing its variability. To represent the spatiotemporal aggregation process, most existing studies focus on the reduced correlation in solar irradiance throughout a plant's spatial distribution. In this paper, we derived a cloud advection model that is instead based upon lagging correlations between upwind/downwind portions of a distributed plant, induced by advection of a fixed cloud pattern over the plant. We use the model to calculate a plant transfer function that can be used to predict the smoothing of the time series. The model was validated using the distributed HOPE-Melpitz measurement dataset, which consisted of 50 solar irradiance sensors at 1 s temporal resolution over a 3 × 2 km2 bounding area. The initial validation showed that the advection-based model outperforms other models at predicting the smoothed irradiance time series during manually identified, advection dominated conditions. We also conducted validation on the model against additional advection dominated periods in the dataset that were identified algorithmically. The cloud advection model's performance compared well to models in literature, but degraded slightly as larger cross-wind plant distributions were investigated. The results in this paper highlight the need to incorporate advection effects on spatial aggregation during advection dominated conditions. Future development of spatiotemporal aggregation models is needed to unify advective models with existing correlation reduction models and to identify regimes where each dominate.
Data about behind-the-meter photovoltaics (PV) installations may be difficult to obtain for researchers. A number of investigators have considered deep learning as an attractive solution to this challenge, capable of directly identifying PV installations from aerial or satellite images. Deep learning models are well known to experience challenges when working with data from sources that they have never been exposed to. This study investigated whether generalizability can be improved by diversifying training data across available labeled data sources. We assessed the performance of models trained on all possible combinations of six different labeled datasets of aerial PV imagery, with a fixed number of total training images. Unfortunately, our results indicate that no combination of model training data achieved generalized performance that approaches models trained on data from a target data source. This implies that generalized ResNet models cannot be developed simply by modifying the configuration of the training data. Consequently, researchers should expect that some degree of data labeling is likely to be necessary when adapting these models to new applications, but our results do indicate that significant performance improvements are possible with only small (∼20%) introductions of target data. Future work may investigate alternative architectures, expanded training datasets, or ways to reduce the amount of labeled data necessary to adapt a model for a given application.
Large-scale photovoltaic plants collect monitoring and operational data at various spatial scales within the plant (e.g., strings, combiners, and inverters). Manual validation of the spatial position of these plant segments relative to the plant design requires on-site observations that may be prohibitively costly or labor intensive. This article presents a methodology for validating plant segment position based on operational data from the plant. By observing the delay between segment responses to cloud motion, predictions of their relative positions within the plant can be made. The method was demonstrated on combiner-level data from a 20-MW, operational photovoltaic plant in the United States. Several instances of apparently mislabeled combiners were identified from the analysis. A partial validation of 20 combiners was conducted by inspecting the plant, with results showing complete agreement between observation and predictions. Predictions derived from this methodology can serve as the basis for further plant inspection and corrective maintenance.