YOUNGJIN SEO

Mr. YOUNGJIN SEO

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 March 2020 in Materials
Verified
Journal Article
Open access
PDF file
YSYOUNGJIN SEO
YOUNGJIN SEO
Dongkyoung LeeDongkyoung Lee
Dongkyoung Lee
Sukhoon PyoSukhoon Pyo
Sukhoon Pyo
This experimental research highlights the applicability of laser cutting to cement-based materials using multimode fiber lasers. A 9 kW multimode fiber laser is used, and the experimental variables are the water-to-cement ratio, laser speed, and material compositions such as cement paste, cement mortar and ultra high performance concrete (UHPC). The laser cutting performance on the cement-based materials is investigated in the downward laser direction. The kerf width and penetration depth of the cement-based materials are quantitatively evaluated with the parameters in the surface and cross section of the specimens after the laser cutting. Moreover, the material removal zone of each specimen is compared in terms of the penetration shapes in the cross-sectional view. Based on experimental observations, the interaction mechanism between the laser and cement-based materials is proposed.

21 June 2018 in Materials
Verified
Journal Article
Open access
PDF file
Dongkyoung LeeDongkyoung Lee
Dongkyoung Lee
YSYOUNGJIN SEO
YOUNGJIN SEO
Sukhoon PyoSukhoon Pyo
Sukhoon Pyo
The results of an experimental investigation on the physical and chemical characteristics of cement-based materials under laser interactions are presented. The laser cutting tests were conducted using a multi-mode continuous fiber laser with a laser power of 1 kW. The experimental variables were laser speed, water to cement ratio, and material compositions including cement paste, cement mortar, and ultra high-performance concrete (UHPC). In order to evaluate the mass removal mechanisms of cement-based materials under laser interactions, the effect of laser cutting was evaluated in terms of kerf width, penetration depth, and chemical composition changes before and after the interaction with laser using EDX analysis. The test results reveal that adding silica sand in cement-based materials leads to decreasing penetration depth and increasing kerf width. Unlike the cement paste and cement mortar series, UHPC specimens showed no discernible crack observed by the naked eye after laser interaction due to its high strength. Furthermore, the chemical analysis indicates that chemical composition changes were caused by various mechanisms including dehydration of calcium hydroxide and thermal decomposition of calcium carbonate.

23 January 2020 in Materials
Verified
Journal Article
Open access
PDF file
YSYOUNGJIN SEO
YOUNGJIN SEO
Dongkyoung LeeDongkyoung Lee
Dongkyoung Lee
Sukhoon PyoSukhoon Pyo
Sukhoon Pyo
Cement-based materials are the most prevalent construction materials, and the conventional cutting techniques are still mostly used for fabricating the materials. However, these conventional cutting methods could generate undesirable micro-cracks and remove unintentional structural sections. This experimental study aims to evaluate the effects of the new fabricating method using laser on the microstructural characteristics of the cement-based materials. The experimental variables are laser cutting speed, water to cement ratio and material compositions. In order to compare the microstructure before and after the laser interaction, the microstructure of the cut surface is observed through scanning electron microscopy/energy dispersive X-Ray (SEM/EDX). After the laser interaction, the Material Removed Zone (MRZ) and Heat Affected Zone (HAZ) are observed on the cut surface. In MRZ, it is found that the glassy layer is thickened by an increasing amount of silicate-based materials in cement-based materials. In addition, it concluded that the amount of silicate-based material mixed in the cement-based materials affects the laser cutting quality.

6 June 2022 in Materials Chemistry and Physics
Verified
Journal Article
Closed access
YSYOUNGJIN SEO
YOUNGJIN SEO
SSSeungik Son
Seungik Son
Dongkyoung LeeDongkyoung Lee
Dongkyoung Lee

31 May 2021 in Materials
Verified
Journal Article
Open access
PDF file
MLMang Muan Lian
Mang Muan Lian
YSYOUNGJIN SEO
YOUNGJIN SEO
Dongkyoung LeeDongkyoung Lee
Dongkyoung Lee
The laser cutting of rock has been popular recently because of its advantages over traditional rock cutting methods. Several types of research were performed to replace traditional rock cutting techniques with laser cutting. The purpose of this experiment is to observe cutting quality for intrusive igneous rocks using a high-power multimode fiber laser. The cutting quality, in terms of kerf width and penetration depth, resulted from different scanning speeds and was studied and compared. The specimens used in this study were gabbro, granite, and diorite, which are widely applied in the construction industry because of their high compressive strength and beautiful textures. Energy-dispersive X-ray Spectroscopy (EDX) analyses were conducted to observe the chemical content of three different areas, the melting area, the burnt area, and a non-processed area, for each rock specimen. The study of the compositional changes in each area will also go over the cutting quality of each rock specimen at different scanning speeds. According to the experimental results, the kerf widths of the specimens gradually decrease as the scanning speeds increase. The penetration depths into the specimens sharply decrease as scanning speeds increase. From a study of their compositional changes, it is found that the cutting quality for each rock depends on their silica content. This study summarizes that the cutting quality for a rock specimen greatly depends on the scanning speed of the laser cutting.

27 November 2021 in Metals
Verified
Journal Article
Open access
PDF file
THTam Van Huynh
Tam Van Huynh
YSYOUNGJIN SEO
YOUNGJIN SEO
Dongkyoung LeeDongkyoung Lee
Dongkyoung Lee
Cement mortar composite has a wide range of applications on construction sites, including masonry, plastering and concrete repair. In construction sites, scabbling process is a method to remove from a few millimeters to several centimeters of defect concrete surfaces. As a result, it is essential to investigate the scabbling characteristics for cement mortar with different silica sand proportion in laser scabbling process. In this study, 5 types of cement mortar with different silica sand proportions in mixing were fabricated and scabbled by using a high-density power laser beam. The effects of silica sand proportion in color changing and penetration depth of the samples after laser scabbling process were studied. Furthermore, the generation of micro-cracks and pores were observed by using scanning electron microscopy (SEM). In addition, chemical composition changes between processed zone and non-processed zone were also evaluated by Energy Dispersive X-ray (EDX) analysis. The results of this study are expected to provide valuable knowledge in understanding of the laser scabbling process for cement-based materials.