Previous studies have focused on the laser cladding of high-entropy alloys (HEAs) on untreated H13 steel, yielding promising results. However, there is limited research on laser cladding HEAs on heat-treated H13 steel, which is more common in the automotive mold industry. In this study, CoCrFeNiAl/WC high-entropy alloy composite coatings were fabricated on heat-treated H13 steel using laser cladding, addressing the gap in applying HEAs on heat-treated tool steels. The influence of the WC content on the phase composition, microstructure, and mechanical properties of the composite coating was investigated. The coating exhibits a dual-layer microstructure consisting of a working layer and a transition layer with different compositions. The results indicate that the CoCrFeNiAl/WC working layer primarily consists of FCC phases. As the WC content increases, metallurgical reactions occur in the working layer, forming (Fe,Co)3W3C, Co4W2C, and Cr7C3 carbide precipitates. This significantly enhances the hardness and wear resistance of the coating, with the final hardness being 1.23 times that of the substrate, the wear weight loss being only 0.21 times that of the substrate, and the average friction coefficient being only 0.82 times that of the substrate.
The mechanism of the pulsed hollow cathode arc welding (HCAW) process was revealed using a fully coupled model with a hollow cathode. We solved the governing equations with the Marangoni effect to study the dynamic behaviors of a molten pool with a square pulsing current (200~400 A, 900 Hz) and varying O2 content; the dynamics of the arc plasma and the weld pool in the HCAW process were investigated quantitatively. The results show that the intensity of the arc plasma was more significantly weakened by the design of the hollow cathode in HCAW than that in GTAW with a solid hollow cathode. We could obtain a stable molten pool even with a large pulsing current section (200 A–400 A) at higher frequencies. The flow dynamics of the molten pool were mainly dominated by the Marangoni effect with varying oxygen content, and we could promote penetration by increasing O2 content in HCAW.
Cavitation resistance in hydraulic machinery requires the turbine and water pump surface to simultaneously possess high hardness and plasticity. To keep the FCC structure of the AlxCoCrFeNi alloy matrix and introduce the particle strengthening effects, the suitable weight content of Cr2AlC particles was calculated and added into Al0.3CoCrFeNi powders. Due to the decomposition of Cr2AlC during laser cladding, the microhardness of Al0.3CoCrFeNi was enhanced by Al atoms and the eutectic-like Cr7C3 structure. In comparison with 5.81 GPa of Al0.3CoCrFeNi coating measured by nanoindentation, the values of the eutectic-like structure and the matrix were measured as 7.76 GPa and 5.93 GPa in 12 wt.% Cr2AlC/Al0.3CoCrFeNi coating. Attributed to the pinning effect of hard Cr7C3 and high plastic matrix, the mass loss was reduced from 7.25 × 10−4 g/mm2 for Al0.3CoCrFeNi coating to 1.91 × 10−4 g/mm2 Cr2AlC/Al0.3CoCrFeNi coating with a ratio of 73.8%.
This study addresses the crack formation problem when laser cladding CoCrFeNiAl high-entropy alloy onto H13 hot-work die steel, aiming to identify suitable transition layer materials. Five nickel-based alloys—Inconel 718, Inconel 625, Hastelloy X, FGH4096, and FGH4169—are selected as alternatives. Three-point bending and hot tensile tests are conducted to assess performance under different stress directions. Test results show that the FGH4096 and FGH4169 coatings fail due to insufficient element diffusion and weak interfacial bonding. Cracks appear at the coating–substrate interface of Inconel 625 and Hastelloy X. In contrast, Inconel 718 performs best, with excellent thermal expansion matching and strong stress resistance. In the three-point bending test, the specimens with Inconel 718 transition layers did not show cracks during the loading process, while specimens with some other alloy transition layers cracked or fractured, which proves that Inconel 718 can effectively enhance the bonding force between the coating and the substrate and improve the material’s performance under bending stress. In the hot tensile test, the stress–strain curve of Inconel 718 is at a high position with a high yield strength, showing excellent resistance to plastic deformation and significantly improving the performance of the nickel-based layer under hot tensile conditions. Therefore, Inconel 718 is identified as the optimal transition layer material.