To address the issues of single-structured feature input channels, insufficient feature learning capabilities in noisy environments, and large model parameter sizes in intelligent diagnostic models for mechanical equipment, a lightweight and efficient multimodal feature fusion convolutional neural network (LEMFN) method is proposed. Compared with existing models, LEMFN captures rich fault features at multiple scales by combining time-domain and frequency-domain signals, thereby enhancing the model’s robustness to noise and improving data adaptability under varying operating conditions. Additionally, the convolutional block attention module (CBAM) and random overlapping sampling technology (ROST) are introduced, and through a feature fusion strategy, the accurate diagnosis of mechanical equipment faults is achieved. Experimental results demonstrate that the proposed method not only possesses high diagnostic accuracy and rapid convergence but also exhibits strong robustness in noisy environments. Finally, a graphical user interface (GUI)-based mechanical equipment fault detection system was developed to promote the practical application of intelligent fault diagnosis in mechanical equipment.
The rolling bearing is one of the commonly used mechanical components in rotating machinery, and its health directly affects the normal operation of equipment. However, the fault signal of rolling bearing is susceptible to noise interference, which makes it difficult to extract the fault characteristics of the rolling bearing and thus affects the accuracy of the diagnosis results. To address this problem, this paper proposes a method by using a snake optimization algorithm to optimize variational mode decomposition (SOA‐VMD) and applies it to the extraction of the fault feature of rolling bearing. First, the minimum Shannon entropy to kurtosis ratio (EKR) is used as the fitness function of SOA to search for the best parameter combination of VMD. Second, the optimized VMD is used to decompose the vibration signal of rolling bearing to obtain K intrinsic mode functions (IMFs). Then, the IMF with the most fault information is selected for reconstruction through EKR. The Teager–Kaiser energy operator (TKEO) spectrum analysis is performed on the reconstructed signal. Finally, this method is used to analyze the simulation signal and rolling bearing vibration signal and compared with empirical mode decomposition (EMD), ensemble empirical mode decomposition (EEMD), and complete ensemble empirical mode decomposition adaptive noise (CEEMDAN) algorithms to verify the feasibility and effectiveness of the SOA‐VMD method.
Convolutional Neural Networks have been widely applied in fault diagnosis tasks of mechanical systems due to their strong feature extraction and classification capabilities. However, they have limitations in handling global context information. Vision Transformers, by leveraging self-attention mechanisms to capture global dependencies, have shown excellent performance in many visual tasks, but often come with high computational costs. Therefore, this paper proposes a lightweight and efficient intelligent fault diagnosis method based on the fusion of Convolutional Network and Vision Transformer features (FCNVT). This method combines the local feature extraction capability of CNNs with the global dependency capturing ability of ViTs, while maintaining computational efficiency. Random overlapping sampling (ROS) techniques are used to preprocess signals, generating two-dimensional synchronized wavelet transform (SWT) images as inputs to the network. Experimental verification has shown that the proposed method achieves up to 100% classification accuracy, with the model having 7 million parameters and a computational cost of only 0.28 G, outperforming other state-of-the-art methods. Finally, a graphical user interface (GUI)-based mechanical equipment fault detection system was developed using this method, which holds positive implications for advancing the practical application of intelligent fault diagnosis in mechanical equipment.
Addressing the issues of a single-feature input channel structure, scarcity of training fault data, and insufficient feature learning capabilities in noisy environments for intelligent diagnostic models of mechanical equipment, we propose a method based on a one-dimensional and two-dimensional dual-channel feature information fusion convolutional neural network (1D_2DIFCNN). By constructing a one-dimensional and two-dimensiona dual-channel feature information fusion convolutional network and introducing a Convolutional Block Attention Mechanism, we utilize Random Overlapping Sampling Technique to process raw vibration signals. The model takes as inputs both one-dimensional data and two-dimensional Continuous Wavelet Transform images. Experimental validation shows that this method exhibits faster convergence, higher diagnostic accuracy, and good robustness and generalization performance on two different datasets, outperforming other advanced algorithms.
In response to the issues of low model recognition accuracy and weak generalization in mechanical equipment fault diagnosis due to scarce data, this paper proposes an innovative solution, a cross-device secondary transfer-learning method based on EGRUN (efficient gated recurrent unit network). This method utilizes continuous wavelet transform (CWT) to transform source domain data into images. The EGRUN model is initially trained, and shallow layer weights are frozen. Subsequently, random overlapping sampling is applied to the target domain data to enhance data and perform secondary transfer learning. The experimental results demonstrate that this method not only significantly improves the model’s ability to learn fault features but also enhances its classification accuracy and generalization performance. Compared to current state-of-the-art algorithms, the model proposed in this study shows faster convergence speed, higher diagnostic accuracy, and superior robustness and generalization, providing an effective approach to address the challenges arising from scarce data and varying operating conditions in practical engineering scenarios.
22 March 2024 in Information Dynamics and Applications
The advent of fifth-generation (5G) long-term evolution (LTE) technology represents a critical leap forward in telecommunications, enabling unprecedented high-speed data transfer essential for today’s digital society. Despite the advantages, the transition introduces significant challenges, including elevated bit error rate (BER), diminished signal-to-noise ratio (SNR), and the risk of jitter, undermining network reliability and efficiency. In response, a novel low-density parity check (LDPC) decoder optimized for 5G LTE applications has been developed. This decoder is tailored to significantly reduce BER and improve SNR, thereby enhancing the performance and reliability of 5G communications networks. Its design accommodates advanced switching and parallel processing capabilities, crucial for handling complex data flows inherent in contemporary telecommunications systems. A distinctive feature of this decoder is its dynamic adaptability in adjusting message sizes and code rates, coupled with the augmentation of throughput via reconfigurable switching operations. These innovations allow for a versatile approach to optimizing 5G networks. Comparative analyses demonstrate the decoder’s superior performance relative to the quasi-cyclic low-density check code (QCLDC) method, evidencing marked improvements in communication quality and system efficiency. The introduction of this LDPC decoder thus marks a significant contribution to the evolution of 5G networks, offering a robust solution to the pressing challenges faced by next-generation communication systems and establishing a new standard for high-speed wireless connectivity.