Clinical application of osteofixation materials is essential in performing maxillofacial surgeries requiring rigid fixation of bone such as trauma surgery, orthognathic surgery, and skeletal reconstruction. In addition to the use of titanium plates and screws, clinical applications and attempts using bioabsorbable materials for osteofixation surgery are increasing with demands to avoid secondary surgery for the removal of plates and screws. Synthetic polymeric plates and screws were developed, reaching satisfactory physical properties comparable to those made with titanium. Although these polymeric materials are actively used in clinical practice, there remain some limitations to be improved. Due to questionable physical strength and cumbersome molding procedures, interests in resorbable metal materials for osteofixation emerged. Magnesium (Mg) gained attention again in the last decade as a new metallic alternative, and numerous animal studies to evaluate the possibility of clinical application of Mg-based materials are being conducted. Thanks to these researches and studies, vascular application of Mg-based biomaterials was successful; however, further studies are required for the clinical application of Mg-based biomaterials for osteofixation, especially in the facial skeleton. The review provides an overview of bioabsorbable osteofixation materials in maxillofacial bone surgery from polymer to Mg.

In this study, we evaluated the bone regenerative capability of a customizable hydroxyapatite (HA) and tricalcium phosphate (TCP) scaffold using a digital light processing (DLP)-type 3D printing system. Twelve healthy adult male beagle dogs were the study subjects. A total of 48 defects were created, with two defects on each side of the mandible in all the dogs. The defect sites in the negative control group (sixteen defects) were left untreated (the NS group), whereas those in the positive control group (sixteen defects) were filled with a particle-type substitute (the PS group). The defect sites in the experimental groups (sixteen defects) were filled with a 3D printed substitute (the 3DS group). Six dogs each were exterminated after healing periods of 4 and 8 weeks. Radiological and histomorphometrical evaluations were then performed. None of the groups showed any specific problems. In radiological evaluation, there was a significant difference in the amount of new bone formation after 4 weeks (p < 0.05) between the PS and 3DS groups. For both of the evaluations, the difference in the total amount of bone after 8 weeks was statistically significant (p < 0.05). There was no statistically significant difference in new bone between the PS and 3DS groups in both evaluations after 8 weeks (p > 0.05). The proposed HA/TCP scaffold without polymers, obtained using the DLP-type 3D printing system, can be applied for bone regeneration. The 3D printing of a HA/TCP scaffold without polymers can be used for fabricating customized bone grafting substitutes.

Medication-related osteonecrosis of the jaw (MRONJ) is one of the most interesting diseases in the field of maxillofacial surgery. In addition to bisphosphonates, the use of antiresorptive and antiangiogenic agents is known to be the leading cause. However, the exact pathogenesis of MRONJ has not been established, and various hypotheses have been proposed, such as oxidative stress-related theory. As a result, a definitive treatment protocol for MRONJ has not been identified, while various therapeutic approaches are applied to manage patients with MRONJ. Although the surgical approach to treat osteomyelitis of the jaw has been proven to be most effective, there are limitations, such as recurrence and delayed healing. Many studies and clinical trials are being conducted to develop another effective therapeutic modality. The use of some materials, including platelet concentrates and bone morphogenetic proteins, showed a positive effect on MRONJ. Among them, teriparatide is currently the most promising material, and it has shown encouraging results when applied to patients with MRONJ. Furthermore, cell therapy using mesenchymal stem cells showed promising results, and it can be the new therapeutic approach for the treatment of MRONJ. This review presents various treatment methods for MRONJ and their limitations while investigating newly developed and researched molecular and cellular therapeutic approaches along with a literature review.

This study evaluated the mechanical properties and bone regeneration ability of 3D-printed pure hydroxyapatite (HA)/tricalcium phosphate (TCP) pure ceramic scaffolds with variable pore architectures. A digital light processing (DLP) 3D printer was used to construct block-type scaffolds containing only HA and TCP after the polymer binder was completely removed by heat treatment. The compressive strength and porosity of the blocks with various structures were measured; scaffolds with different pore sizes were implanted in rabbit calvarial models. The animals were observed for eight weeks, and six animals were euthanized in the fourth and eighth weeks. Then, the specimens were evaluated using radiological and histological analyses. Larger scaffold pore sizes resulted in enhanced bone formation after four weeks (p < 0.05). However, in the eighth week, a correlation between pore size and bone formation was not observed (p > 0.05). The findings showed that various pore architectures of HA/TCP scaffolds can be achieved using DLP 3D printing, which can be a valuable tool for optimizing bone-scaffold properties for specific clinical treatments. As the pore size only influenced bone regeneration in the initial stage, further studies are required for pore-size optimization to balance the initial bone regeneration and mechanical strength of the scaffold.

Chronic periodontitis is the most common disease which induces oral tissue destruction. The goal of periodontal treatment is to reduce inflammation and regenerate the defects. As the structure of periodontium is composed of four types of different tissue (cementum, alveolar bone periodontal ligament, and gingiva), the regeneration should allow different cell proliferation in the separated spaces. Guided tissue regeneration (GTR) and guided bone regeneration (GBR) were introduced to prevent epithelial growth into the alveolar bone space. In the past, non-absorbable membranes with basic functions such as space maintenance were used with bone graft materials. Due to several limitations of the non-absorbable membranes, membranes of the second and third generation equipped with controlled absorbability, and a functional layer releasing growth factors or antimicrobials were introduced. Moreover, tissue engineering using biomaterials enabled faster and more stable tissue regeneration. The scaffold with three-dimensional structures manufactured by computer-aided design and manufacturing (CAD/CAM) showed high biocompatibility, and promoted cell infiltration and revascularization. In the future, using the cell sheath, pre-vascularizing and bioprinting techniques will be applied to the membrane to mimic the original tissue itself. The aim of the review was not only to understand the past and the present trends of GTR and GBR, but also to be used as a guide for a proper future of regeneration therapy in the oral region.

Background: Chronic periodontitis is a multifactorial inflammatory disease resulting in patients exhibiting high levels of inflammatory factors causing systemic inflammatory bone destruction that may lead to osteoporosis development. The association between periodontitis and osteoporosis has been documented; however, the findings remain unclear. This study aimed to identify the association between periodontitis and osteoporosis using a cross-sectional study design and Korean Genome and Epidemiology Study (KoGES) health examinee data.Methods: This cross-sectional study used epidemiological data from the KoGES during 2004–2016. Of 125,324 participants (age, 40–79 years), 9969 with periodontitis and 115,332 controls (without periodontitis) were selected. We analyzed the history of osteoporosis and fractures of all participants. All participants were examined according to age, sex, income group, obesity, smoking habits, alcohol consumption, and food intake. To analyze the odds ratio (OR) of periodontitis for those with osteoporosis and fractures, a logistic regression model was used.Results: The adjusted odds ratio (aOR) of periodontitis for osteoporosis was 2.16 (95% confidence interval [CI], 2.01–2.31;P < 0.001). The aOR of periodontitis for any fracture was 1.54 (95% CI 1.46–1.62;P < 0.001).Conclusion: Osteoporosis and fractures are associated with periodontitis. Performing regular oral hygiene and examinations of bone mineral density are recommended to prevent aggravation of osteoporosis and periodontitis.