Future Video Coding (FVC) is a new international video compression standard offering much better compression efficiency than previous video compression standards at the expense of much higher computational complexity. In this paper, two different high performance FVC 2D transform hardware are designed and implemented using Verilog HDL. They are the first FVC 2D transform hardware in the literature. They perform 2D DCT-II, DCT-V, DCT-VIII, DST-I, and DST-VII operations for 4x4 and 8x8 transform units. The first (baseline) hardware uses separate datapaths for each 1D transform. Since the second (reconfigurable) hardware uses two reconfigurable datapaths for all 1D transforms, it has smaller area than the baseline hardware. Since the baseline hardware uses data gating technique, it has lower energy consumption than the reconfigurable hardware. Therefore, the proposed FVC baseline 2D transform hardware can be used in high performance and low energy FVC encoders. The proposed FVC reconfigurable 2D transform hardware can be used in high performance and low cost FVC encoders.
Intra prediction algorithm in the recently developed High Efficiency Video Coding (HEVC) standard has very high computational complexity. Therefore, in this paper, we propose novel techniques for reducing amount of computations performed by HEVC intra prediction algorithm, and therefore reducing energy consumption of HEVC intra prediction hardware. The proposed techniques significantly reduce the amount of computations performed by 4×4 and 8×8 angular prediction modes with a small comparison overhead without any PSNR and bit rate loss. We also designed and implemented a high performance HEVC intra prediction hardware for 4×4 and 8×8 angular prediction modes including the proposed techniques using Verilog HDL, and mapped it to a Xilinx Virtex 6 FPGA. The proposed techniques significantly reduce the energy consumption of the proposed hardware on this FPGA.
19 July 2016 in IEEE Transactions on Consumer Electronics
In this paper, a novel computation and energy reduction technique for High Efficiency Video Coding (HEVC) Discrete Cosine Transform (DCT) for all Transform Unit (TU) sizes is proposed. The proposed technique reduces the computational complexity of HEVC DCT significantly at the expense of slight decrease in PSNR and slight increase in bit rate by only calculating several pre-determined low frequency coefficients of TUs and assuming that the remaining coefficients are zero. It reduced the execution time of HEVC HM software encoder up to 12.74%, and it reduced the execution time of DCT operations in HEVC HM software encoder up to 37.27%. In this paper, a low energy HEVC 2D DCT hardware for all TU sizes is also designed and implemented using Verilog HDL. The proposed hardware, in the worst case, can process 53 Ultra HD (7680x4320) video frames per second. The proposed technique reduced the energy consumption of this hardware up to 18.9%. Therefore, it can be used in portable consumer electronics products that require a real-time HEVC encoder.
1 November 2014 in IEEE Transactions on Consumer Electronics
In this paper, a novel energy reduction technique for High Efficiency Video Coding (HEVC) Inverse Discrete Cosine Transform (IDCT) and Inverse Discrete Sine Transform (IDST) for all transform unit (TU) sizes is proposed. The proposed technique calculates IDCT and IDST only for DC coefficient if the values of several predetermined forward transformed low frequency coefficients in a TU are smaller than a threshold. The proposed technique reduces the computational complexity of IDCT and IDST significantly. It increases the bit rate slightly for most video frames. It decreases the PSNR slightly for some video frames, and it increases the PSNR slightly for some video frames. In this paper, a low energy HEVC 2D inverse transform (IDCT and IDST) hardware for all TU sizes is also designed and implemented using Verilog HDL. In the worst case, the proposed hardware can process 48 Quad HD (3840x2160) video frames per second. The proposed technique reduced the energy consumption of this hardware up to 32%. Therefore, the proposed hardware can be used in portable consumer electronics products that require a real-time HEVC encoder.
Sub-pixel interpolation is one of the most computationally intensive parts of High Efficiency Video Coding (HEVC) video encoder and decoder. Therefore, in this paper, a low energy HEVC sub-pixel (half-pixel and quarter-pixel) interpolation hardware, which uses Hcub multiplierless constant multiplication algorithm, is proposed. The proposed HEVC sub-pixel interpolation hardware, in the worst case, can process 30 quad full HD (3840×2160) video frames per second. It has up to 48% less energy consumption than original HEVC sub-pixel interpolation hardware.
Fractional interpolation is one of the most computationally complex parts of video compression standards. Fractional interpolation in Versatile Video Coding (VVC) standard has much higher computational complexity than fractional interpolation in previous video compression standards. In this paper, a reconfigurable VVC fractional interpolation hardware for motion compensation is designed and implemented using Verilog HDL. The proposed hardware is the first VVC fractional interpolation hardware for motion compensation in the literature. It interpolates necessary fractional pixels for 1/16 pixel accuracy for all prediction unit sizes. The proposed VVC fractional interpolation hardware, in the worst case, can process 66 quad full HD (3840×2160) frames per second. It has up to 77% less power consumption than baseline VVC fractional interpolation hardware.